CUDAHY, Circuit Judge.
Petitioner Faultless Division, Bliss & Laughlin Industries, Inc. (“Faultless”) seeks judicial review of an order of the Occupational Safety and Health Review Commission (“Commission” or “OSHRC”) citing [1180]*1180Faultless for failing to guard certain presses. On December 4 and 5, 1979, a compliance officer from the Occupational Safety and Health Administration (“OSHA”) inspected Faultless’ rubber molding operations. As a result of this inspection, Faultless was cited for a serious violation of 29 C.F.R. § 1910.212(a)(3)(h) (1980), for failing to guard the point of operation on 17 hydraulic rubber molding presses. The Secretary established an abatement date and assessed a corrected penalty of $560 (later reduced to $100). Faultless contested the citation and the Commission assigned the case to an Administrative Law Judge (“ALJ”). The ALJ upheld the citation.
Faultless here petitions for review of the AU’s decision and order, which became the Commission’s final order on March 25, 1981, when no Commissioner granted Faultless’ petition for discretionary review. See 29 U.S.C. § 666(i) (Supp. II 1978). In its petition, Faultless asserts that the Commission’s final order lacks substantial eviden-tiary support, is based upon an unconstitutionally vague regulation and wrongfully imposes upon it the burden of proving infeasibility of compliance. We deny Faultless’ petition and affirm the Commission’s order.1
I.
Faultless manufactures small rubber caster wheels at its plant in Evansville, Indiana. As part of its manufacturing process, Faultless operates 17 hydraulic rubber molding presses. These presses employ both pressure and heat to form small rubber “preforms” into wheel-shaped casters. There are two types of presses at the plant arrayed along two separate production lines. Line A contains twelve “French-type” hydraulic rubber molding presses; Line B contains five “clam shell” hydraulic rubber molding presses. The two types of presses are similar in structure and operation except that the French-type is a two-sided press requiring two operators to simultaneously load and operate the press, while the clam shell presses need only one operator loading from one side.
Operators load the press dies while standing at the side of the press on a work platform. Line B operators pull a mold out of the clam shell press, insert the rubber preforms in the mold, and then close the mold and push it back into the press. Line A operators, however, push sheets containing the preforms directly into the French-type press. The preforms are held in place on the sheets by a jig board located on top of the sheet. After inserting the sheet and jig board, the operators pull the sheet out of the press and then shake the board to position the preforms on guiding pins. The operators then pull the jig board out of the press and the preforms drop into the molding cavities. Unlike the Line B clam shell operation, the mold used on Line A is not closed outside the press; instead, the mold remains stationary (positioned inside the press) and the die with exposed preforms is lifted upward against the stationary mold by the action of the closing press.
On both lines, after the preforms are loaded into the press, the operator activates the press by depressing a momentary-contact start button located near the press opening. (The paired Line A operators must simultaneously depress the start buttons located on the two sides of the press.) Immediately after depressing the start button (or buttons), the ram of the press in question lifts hydraulically upward, closing the gap or opening which exists at the point of operation. Depending upon the thickness of the die, the opening at the point of operation for Line B presses varies from three to seven inches in height and the time taken for the ram to close is approximately seven seconds.
[1181]*1181The opening at the point of operation for Line A presses varies from seven to eleven inches in height and closing is completed in approximately ten seconds. After a press is closed, a curing cycle begins (during which the press remains closed). This cycle varies in duration from 10 to 45 minutes. When curing is completed, an automatic timer releases the press ram, the opening at the point of operation reappears and the finished wheel casters are ready for unloading. The press operators move from press to press, alternately loading and unloading the presses as time permits.
The OSHA compliance officer found no guarding device on the presses at the time of his inspection. The only safety device presently guarding the presses is a single emergency stop button. The activation of the stop button releases the hydraulic pressure, permitting the press ram to descend to the press base and restoring the opening at the point of operation. This button is located approximately six feet above the work platform on the upper left side of the press.
Faultless disputes the ALJ’s findings of fact pertaining to the operators’ behavior after they activate the presses. Based upon the testimony of a former Faultless production supervisor (La Mar), the ALJ found that press operators often reach into the press mold area during the closing cycle to realign preforms, thereby attempting to prevent the molding of imperfect caster wheels and reducing the potential for damage to the press. Given this reaching into
the press mold area, if the operator should be unable to remove his hand or arm before the ram completed its closing cycle, his limb would be crushed or amputated by the powerful thrust of the press ram. The ALJ foresaw an increased possibility of such an unfortunate accident resulting from Faultless’ work rule requiring operators to wear long-sleeved shirts; an operator wearing long sleeves might entangle his shirt in the numerous recessed pins and guidepins inside the press mold. La Mar also testified that an operator who entangled his left arm shirt sleeve in the mold probably could not reach the emergency stop button located on the upper left side of the press with his free right hand. The ALJ made a finding, which Faultless challenges, that press operators stand near the presses and watch the seven to ten second closing cycle before walking to the next press.
After hearing the evidence adduced by both parties, the ALJ concluded that Faultless failed to guard its hydraulic rubber molding presses as required by 29 C.F.R. § 1910.212(a)(3)(H) (1980).2 The ALJ also concluded that this failure constituted a serious violation of the Occupational Safety and Health Act (the “OSH Act”).3 On this petition for review, Faultless reiterates its arguments raised before the ALJ together with several new contentions. Because of the unique factual setting of this case and some apparent misconceptions about the applicable law, we shall discuss each of Faultless’ contentions in detail.
[1182]*1182II.
Faultless contends that the ALJ’s findings (which were, of course, adopted by the Commission) lack substantial evidentiary support in the whole record. As one branch of this contention, Faultless asserts that the ALJ’s alleged preconception of the merits precluded him from rendering an impartial and objective decision. Moreover, Faultless claims that the ALJ improperly relied on the testimony of an admittedly biased witness and that other factual findings contradict Faultless’ unrebutted testimony and evidence.
Our standard of review of the ALJ’s findings of fact is provided by the OSH Act. Thus, section 11(a) of the OSH Act, 29 U.S.C. § 660(a) (1976), provides that “[t]he findings of the Commission with respect to questions of fact, if supported by substantial evidence on the record considered as a whole, shall be conclusive.” Although this standard does not permit or require us to rubber stamp Commission findings, we are clearly required to accept the ALJ’s (and by adoption, the Commission’s) reasonable and substantial findings of fact and the inferences drawn by the Commission from these findings. See International Harvester Co. v. OSHRC, 628 F.2d 982, 986-87 (7th Cir. 1980); RMI Co. v. Secretary of Labor, 594 F.2d 566 (6th Cir. 1979). Further, under the applicable standard, the ALJ’s credibility determinations must be honored by the agency and by a reviewing court unless these determinations are contradicted by uncontrovertible evidence. International Harvester, 628 F.2d at 986. Finally, our review of the ALJ’s findings is premised upon an understanding of the OSH Act’s remedial purpose and broad scope. See 29 U.S.C. § 651 (1976); Whirlpool Corp. v. Marshall, 445 U.S. 1, 11-12, 100 S.Ct. 883, 890-91, 63 L.Ed.2d 154 (1980); Bratton Corp. v. OSHRC, 590 F.2d 273, 276 77 (8th Cir. 1979).
In connection with its challenge to the Commission findings, Faultless directs our attention to several parts of the record which, in its opinion, demonstrate the ALJ’s bias against Faultless. Thus as part of its case, Faultless offered into evidence a video tape display of a French-type hydraulic rubber molding press in operation. At the time of this offer, the ALJ told Faultless’ counsel that he was familiar with the machine in question and indicated to counsel that the display was not necessary.4 Faultless points out that, before the colloquy about the tape, the ALJ denied a motion by Faultless to dismiss the citation, relying on an earlier case which had allegedly been decided by the ALJ.5 Additionally, Faultless asserts that the ALJ’s bias is demonstrated by his crediting of the testimony of Faultless’ former supervisor, La Mar. An admittedly biased witness,6 La Mar testified that he personally observed press operators reach into the press to straighten misaligned parts as the ram ascended. Faultless contends that its witnesses contradicted La Mar’s testimony and thus, the ALJ improperly credited biased evidence.
[1183]*1183We arc unpersuaded by Faultless’ arguments. Although an ALJ’s bias may be grounds for overturning factual determinations, see Medline Industries, Inc. v. NLRB, 593 F.2d 788, 795 (7th Cir. 1979) (dicta), the evidence does not in fact raise any substantial doubt about the ALJ’s impartiality in this case. Mere familiarity with legal or factual issues involved in a particular case does not, in itself, evince an adjudicator’s biased predisposition. See United Steelworkers of America v. Marshall, 647 F.2d 1189, 1208-09 (D.C.Cir.1980), cert denied sub nom. Lead Industries Association v. Donovan, 453 U.S. 913, 101 S.Ct. 3148, 3149, 69 L.Ed.2d 997 (1981). Likewise, we are unpersuaded that the ALJ’s denial of Faultless’ motion to dismiss, relying upon previous decisions, which Faultless erroneously argued were heard and decided by the same ALJ, demonstrates an unacceptable preconception of the merits of this case. If we should accept Faultless’ argument, even an unarguably even-handed administrative adjudicator could be taxed with bias merely for relying on his own prior decisions. Here we believe that the ALJ’s comments about the video tape display were intended simply to avoid wasting valuable hearing time. The ALJ’s attitude does not demonstrate bias against Faultless or .its point of view.
We also reject Faultless’ contention that the AU exhibited bias by crediting La Mar’s testimony. The ALJ carefully considered La Mar’s bias when assessing this evidence. No one directly contradicted La Mar’s crucial observation that operators actually placed their hands inside the presses during the closing cycle. Faultless’ witnesses (who are. also at least potentially susceptible to charges of bias) merely noted that they had never personally observed an operator place his hand inside a press.7 The OSHA compliance officer also testified that operators could reach into a closing press, although he did not observe any operator reach into a closing press during his compliance inspection. Finally, the ALJ carefully compared all of La Mar’s testimony with the testimony given by Faultless’ witnesses, finding that there were no material contradictions between the two sets of testimony. Under such circumstances, we cannot find error based on a demonstration of bias.8
As noted above, apart from its allegation of bias, Faultless attacks the ALJ’s factual findings as lacking substantial evidentiary support in the record. According to Faultless, the ALJ’s finding that the press operators would stand at their work platforms, after activating the press closure cycle, to observe their presses close contradicts the ’unrebutted testimony of Faultless’ witnesses. Moreover, the ALJ allegedly ignored the testimony of Faultless’ witnesses who claimed that the operators realigned any misplaced rubber preforms before activating the press. These findings are crucial because Faultless argues that the operators habitually walked over to the press next in line immediately after activating the closure cycle and, thus, were not in a position to extend their hands into the closing press.
The ALJ’s findings with respect to these matters are supported by substantial evidence. Faultless does not refer us to [1184]*1184any definitive statement by a Faultless witness to the effect that the operators never stood near the presses to observe the relatively short seven to ten second closing cycle. Nor does our own review of the record disclose such a statement. Faultless’ witnesses merely testified that, as part of their prescribed production method, operators were expected to move “immediately” to the next press. Absent any clear rebuttal of La Mar’s claim that operators did stand and observe the presses close, we cannot conclude that this finding is unsupported by substantial evidence. Further, we think that Faultless’ argument probably belies typical human behavior in a factory. An experienced factfinder might question Faultless’ attempt to persuade him that its press operators, in their zeal to meet production schedules, raced from press to press, never stopping to pause for a few seconds as the press closed. A more credible view, as the ALJ inferred from this record, is that a press operator on occasion might watch the press close to insure that nothing went wrong before the curing cycle began.
Likewise, we conclude that the ALJ’s finding that press operators would reach into closing presses to realign rubber preforms is supported by substantial evidence. Obviously, safety-conscious operators would, as Faultless’ witnesses testified, make every effort to realign the preforms before activating the press. Faultless’ witnesses, however, testified only that they never observed an operator place his hand inside a closing press. Obviously, Faultless does not assert that operators could not as a matter of fact place their hands inside a closing press. La Mar, on the other hand, testified that, based on over sixteen years of day to day experience working with these machines and their operators, he personally observed operators place their hands inside a press as it closed.
Finally, we note that substantial evidence, considering the whole record, supports the ALJ’s conclusion that Faultless committed a serious violation of the machine guarding regulation. The Secretary’s regulation requires that “[t]he point of operation of machines whose operation exposes an employee to injury, shall be guarded.” 29 C.F.R. § 1910.212(a)(3)(ii) (1980). It is undisputed that Faultless’ hydraulic rubber molding presses were unguarded. Nor does Faultless contend that an operator’s hand or arm would not be crushed or amputated if the press ram closed on it or that an operator is physically incapable of reaching into a closing press.9 Citing its commendable history of there having been no serious accidents involving these presses,10 Faultless argues that the unguarded presses are not a safety hazard. Although the absence of accidents is entitled to great weight, this fact alone is not dispositive of the question whether a violation has occurred. A. E. Burgess Leather Co. v. OSHRC, 576 F.2d 948, 951 (1st Cir. 1978); Allis-Chalmers Corp. v. OSHRC, 542 F.2d 27, 30-31 (7th Cir. 1976); cf. Kent Nowlin Construction Co. v. OSHRC, 593 F.2d 368 (10th Cir. 1979) (unlikelihood of injury not dispositive when specific regulatory standard violated). This court would be derelict in its responsibilities under the OSH Act if we were to wait until an operator lost an arm and a livelihood in the crushing grip of these presses. See [1185]*1185Long Manufacturing Co. v. OSHRC, 554 F.2d 903, 904-05 (8th Cir. 1977) (“The risk of serious and mangling injuries to workers [operating power presses] whose hands or arms are caught by a descending die is obvious and has long been recognized.”) Indeed, “[t]he goal of the [OSH] Act is to prevent the first accident, not to serve as a source of consolation for the first victim or his survivors.” Mineral Industries & Heavy Construction Group v. OSHRC, 639 F.2d 1289, 1294 (5th Cir. 1981).
III.
Faultless contends that the Secretary’s application of the machine guarding standard to it violated due process because the standard’s requirements are impermissibly vague. We believe that Faultless misunderstands the law.
First, Faultless premises its vagueness argument on its characterization of the machine guarding standard as a “performance” rather than a “specification” standard. According to Faultless, the courts and the Commission have struck down performance standards as unconstitutionally vague unless the standard’s scope is limited by extrinsic norms, including industry eus-toms and practices. Because, in the rubber industry, hydraulic rubber molding presses are not customarily guarded, Faultless asserts that application of the machine guarding standard does not provide it with sufficient and fair warning. Second, Faultless argues that the regulation is vague because other regulations specifically exempt its presses from any guarding requirements.
When considering remedial legislation such as the OSH Act and its implementing regulations, the purported vagueness of a standard is judged not on its face but rather in the light of its application to the facts of the case. PBR, Inc. v. Secretary of Labor, 643 F.2d 890, 897 (1st Cir. 1981); McLean Trucking Co. v. OSHRC, 503 F.2d 8, 10-11 (4th Cir. 1974). Moreover, the regulations will pass constitutional muster ■even though they are not drafted with the utmost precision; all that due process requires is a fair and reasonable warning. Allis-Chalmers Corp. v. OSHRC, 542 F.2d 27, 30 (7th Cir. 1976). The constitution does not demand that the employer be actually aware that the regulation is applicable to his conduct or that a hazardous condition exists.11
[1186]*1186We begin our analysis by noting that by its title — “General requirements for all machines” — the regulation on its face appears to apply to Faultless’ hydraulic presses. 29 C.F.R. § 1910.212 (1980) (emphasis supplied.12 Subdivision (a)(3)(ii) states that the point of operation of a machine “shall be guarded,” and subdivision (aX3)(iv) lists “some of the machines which usually require point of operation guarding,” including “power-presses.” 29 C.F.R. §§ 1910.212(a)(3)(h) & (iv) (1980) (emphasis supplied). The methods of compliance are illustrated, in 29 C.F.R. § 1910.212(a)(1) (1980), by several nonexhaustive examples of point of operation guarding. Considered in the context of Faultless’ hydraulic presses, which are encompassed not only within the generic term “power-presses” but also within the mandate of the regulation’s application to “all machines,” and given the need for guards on such presses to prevent injuries as a matter of elementary industrial safety,13 we cannot conclude that the regulation as applied is unconstitutionally vague.14 We note that other courts have similarly concluded that the regulation in question applies to all machines, Irvington Moore, Division of U. S. Natural Resources, Inc. v. OSHRC, 556 F.2d 431 (9th Cir. 1977); Long Manufacturing Co., N.C. Inc. v. OSHRC, 554 F.2d 903 (8th Cir. 1977), and is not unconstitutionally vague as applied in other like situations. A.E. Burgess Leather Co. v. OSHRC, 576 F.2d 948 (1st Cir. 1978); Long, 554 F.2d at 907; cf. PBR, Inc. v. Secretary of Labor, 643 F.2d 890 (1st Cir. 1981) (29 C.F.R. § 1910.212(a)(1) not unconstitutionally vague when applied to railroad undercutter).15
In construing the regulation before us, we decline Faultless’ invitation in effect to characterize the provision as “very general,” “unclear,” or a “performance standard” in order to lay the predicate for considering evidence of industry custom and practice. Faultless correctly notes that some courts have considered evidence of industry practice when construing very general or unclear regulations. Indeed, we note that industry practice may be relevant in limited situations to avoid prejudicing a party by the application of a generalized statute or regulation of unfocused import. Prejudice might arise when the regulatory impact resulted in a complex and costly compliance program in cases where there was no reasonable expectation that the regulation was applicable to the questioned conduct. The instant case, however, does not require or permit consideration of industry practice for the purpose of defining machine guarding requirements since we are confronted with a clearly applicable, unarguable and specific regulation on the subject in question. In general, courts have considered industry practice. evidence only when a specific standard of expected employer conduct is proposed to be derived from a very general statutory or regulatory [1187]*1187command. See, e.g., Kropp Forge Co. v. Secretary of Labor, 657 F.2d 119 (7th Cir. 1981) (noise regulation — 29 C.F.R. § 1910.95(b) (1980)); S & H Riggers & Erectors, Inc. v. OSHRC, 659 F.2d 1273 (5th Cir. 1981) (personal protective equipment for construction industry—29 C.F.R. § 1926.28(a) (1980)); Pratt & Whitney Aircraft, Division of United Technologies Corp. v. Secretary of Labor, 649 F.2d 96, 100-01 (2d Cir. 1981) (general duty clause — 29 U.S.C. § 654(a)(1) (1976)); Donovan v. Royal Logging Co., 645 F.2d 822, 830, 831 (9th Cir. 1981) (general duty clause—29 U.S.C. § 654(a)(1) (1976)); R. L. Sanders Roofing Co. v. OSHRC, 620 F.2d 97 (5th Cir. 1980) (general duty clause—29 U.S.C. § 654(a)(1) (1976)); B & B Insulation, Inc. v. OSHRC, 583 F.2d 1364 (5th Cir. 1978) (personal protective equipment for construction industry—29 C.F.R. § 1926.28(a) (1980));16 American Airlines, Inc. v. Secretary of Labor, 578 F.2d 38 (2d Cir. 1978) (personal protective equipment—29 C.F.R. § 1910.132 (1980)); Cape & Vineyard Division, New Bedford Gas and Edison Light Co. v. OSHRC, 512 F.2d 1148 (1st Cir. 1975) (personal protective equipment—29 C.F.R. § 1910.132 (1980)).17
The regulation here, on the other hand, unlike regulations relating, for example, to noise or to personal protective equipment, or to the general duty clause regulations, is sufficiently specific as to the machines affected and as to the methods of compliance to reasonably apprise Faultless in clear terms that its presses must be guarded. The machine-guarding regulation applies to all machines, defines the areas that must be guarded, states what an effective guarding device must achieve and even provides several examples of guarding devices. Neither the noise regulation standard nor the personal protective equipment standard nor the general duty clause are comparably specific. We agree with the holding of A. E. Burgess Leather Co. v. OSHRC, 576 F.2d 948 (1st Cir. 1978), that industry practice ■should not be considered when construing the regulation before us because the standard for employer conduct is quite specific and essentially requires no such construction.
Our position follows without question from the stated purposes of the OSH Act. On the other hand, carried to its logical conclusion, Faultless’ argument for reliance on industry practice would permit employers to avoid compliance with specific safety mandates by relying on the (perhaps equally objectionable) practices of their peers. Cf. Voegele Co. v. OSHRC, 625 F.2d 1075, 1078-79 (3rd Cir. 1980) (even those courts that consider industry custom and practice do not ignore reasonable person test because to do so would allow entire industries to avoid liability for unsafe conditions). Nothing in the OSH Act or its legislative history requires or permits the Secretary to await an industry consensus about unsafe conditions before moving to enforce. See Bristol Steel & Iron Works, Inc. v. OSHRC, 601 F.2d 717 (4th Cir. 1979).18
[1188]*1188Faultless also asserts, we think erroneously, that because its presses are either exempted or not covered under other machine-guarding regulations, the Secretary’s application of 29 C.F.R. § 1910.-212(a)(3)(ii) (1980) violates due process. Thus, although 29 C.F.R. § 1910.216 (1980) is, as Faultless argues, applicable to the rubber and plastics industries, this regulation contains more detailed guarding requirements applicable only to mills and calenders. But hydraulic rubber molding presses are not within the definition either of a mill or of a calendar. See 29 C.F.R. §§ 1910.211(c)(2)-(3) (1980). Faultless further contends that its presses are excluded from the more specific guarding requirements of 29 C.F.R. § 1910.217 (1980) applicable to power presses and, therefore, this “specific” regulation must govern as against the “general” language of 29 C.F.R. § 1910.212 (1980). Even if Faultless’ presses are thought to be excluded from section 1910.217 (and we do not decide this question here), the exclusions in section 1910.-217(a)(5) apply only to the detailed guarding requirements contained in that section of the regulations. Exclusion of a machine from the requirements of section 1910.217 does not preclude application to it of the guarding requirements of section 1910.212. This conclusion is clear because the latter regulation, by its terms, applies to all machines.
The OSH Act regulations expressly provide that exclusion under certain specific regulatory commands does not preclude application of the slightly more generalized, albeit explicitly comprehensive, command of another regulation. See 29 C.F.R. § 1910.5(c)(2) (1980). The courts that have considered the relationship between section 1910.217 and section 1910.212 have unanimously concluded that a machine exempted under section 1910.217 continues to be covered under 1910.212. Diebold, Inc. v. Marshall, 585 F.2d 1327, 1334 (6th Cir. 1978);19 Irvington Moore, Division of U. S. Natural Resources, Inc. v. OSHRC, 556 F.2d 431, 435 (9th Cir. 1977); Long Manufacturing Co., N. C. Inc., v. OSHRC, 554 F.2d 903, 908 (8th Cir. 1977). As noted in Diebold, appellate courts will not overturn the “Commission’s reasonable interpretations of the Secretary’s regulations.” 585 F.2d at 1334 (footnote omitted).20 Thus, we find no merit in Faultless’ claim of a due process violation.21
[1189]*1189IV.
Faultless’ final contention is that the ALJ improperly imposed upon it the burden of proving the infeasibility of the Secretary’s compliance order. In addition, and regardless of any applicable burden of proof, Faultless argues that the ALJ erred in holding that the evidence Faultless presented on the feasibility issue was insufficient. We shall consider each contention separately.
As to the first, courts have placed the burden of demonstrating the feasibility of a proposed compliance order on the Secretary in only two situations. First, the Secretary must demonstrate the feasibility of any remedial administrative or engineering controls ordered under 29 C.F.R. § 1910.-95(b)(1) (1980) (the noise regulation standard). See Diversified Industries Division, Independent Stave Co. v. OSHRC, 618 F.2d 30 (8th Cir. 1980); RMI Co. v. Secretary of Labor, 594 F.2d 566 (6th Cir. 1979); Turner Co. Division of Olin Corp. v. Secretary of Labor, 561 F.2d 82 (7th Cir. 1977). The justification for placing the burden on the Secretary in noise regulation cases is that the Secretary is explicitly required by the regulation to consider feasibility before issuing a compliance order. Second, the Secretary must demonstrate the feasibility of a compliance order issued under a regulation that does not, on its face, expressly provide for any particular means of compliance. See Donovan v. Royal Logging Co., 645 F.2d 822, 829 (9th Cir. 1981) (general duty clause); Ray Evers Welding Co. v. OSHRC, 625 F.2d 726, 733 (6th Cir. 1980) (personal protective equipment regulation); Bristol Steel & Iron Works, Inc. v. OSHRC, 601 F.2d 717, 723-24 (4th Cir. 1979) (personal protective equipment regulation); General Electric Co. v. OSHRC, 540 F.2d 67, 69-70 (2d Cir. 1976) (eye protection regulation); National Realty and Construction Co. v. OSHRC, 489 F.2d 1257, 1268 (D.C.Cir.1973) (general duty clause). It is indeed appropriate for the Secretary to carry the burden in such cases when the compliance remedy is based upon a very general statutory or regulatory command that does not describe for the employer any specific methods for compliance.
Unlike the regulations involved in the above cited cases, the machine-guarding regulation does specify several ways for an employer to comply with its standards. Three specific guarding techniques — “barrier guards, two-hand tripping devices [and] electronic safety devices” are set out in the regulation. 29 C.F.R. § 1910.212(a)(1) (1980); see Ace Sheeting & Repair Co. v. OSHRC, 555 F.2d 439 (5th Cir. 1977). Applying a like analysis to particularized standards, the First Circuit in A. E. Burgess Leather Co. v. OSHRC, 576 F.2d 948, 952 (1978) held that the employer, not the Secretary, must carry the burden of establishing infeasibility when the compliance order is issued under the “specific” standards in 29 C.F.R. § 1910.212(a)(3)(ii). Accord, PBR, Inc. v. Secretary of Labor, 643 F.2d 890, 897 (1st Cir. 1981). Thus, we conclude that the ALJ properly placed the burden of demonstrating infeasibility upon Faultless.
On the question of sufficiency of the evidence of infeasibility, after reviewing the evidence presented by Faultless on these issues, we conclude that the ALJ properly held that Faultless failed to demonstrate the infeasibility of complying with the Secretary’s order. Feasibility, in the context of safety regulations, refers not only to technical feasibility but also to economic feasibility. See International Harvester Co. v. OSHRC, 628 F.2d 982, 987-89 (7th Cir. 1980); A. E. Burgess Leather Co. v. OSHRC, 576 F.2d 948, 951 n.2 (1st Cir. 1978); Turner Co. Division of Olin Corp. v. Secretary of Labor, 561 F.2d 82, 85-86 (7th [1190]*1190Cir. 1977). We note first that Faultless did not argue either before the ALJ or on this appeal that it was technologically infeasible to install some type of point of operation guarding device on its presses. Thus, we are left only with the issue of economic feasibility.
A successful economic feasibility argument must demonstrate both that it is extremely costly for the employer to comply with the Secretary’s order and that the employer cannot absorb this cost. Faultless claims that two-hand controls would increase its yearly operating costs by $116,000 (lost production time and capacity); in addition, Faultless has alleged that it would expend $82,000 for new presses to make up for lost production time generated by the use of two-hand controls together with $34,-000 to install the two-hand controls. This evidence alone, however, does not demonstrate economic infeasibility. Faultless has not alleged or demonstrated that it cannot absorb or pass on in the price of the product this added expense. Although the expense of installing two-hand controls may be somewhat burdensome, economic infeasibility is established only when the employer’s existence as an entity is financially imperiled by compliance. See Arkansas-Best Freight Systems, Inc. v. OSHRC, 529 F.2d 649, 654 (8th Cir. 1976); cf. Industrial Union Department, AFL-CIO v. Hodgson, 499 F.2d 467, 478 (D.C.Cir.1974) (OSH Act contemplates demise of employers who cannot comply with safety standards); National Realty and Construction Co. v. OSHRC, 489 F.2d 1257, 1266 n.37 (D.C.Cir.1973) (if cost to implement precautionary measure threatens employer’s economic vitality, this precaution should be proposed by regulation and not by compliance order). With respect to the economic burdens what ideally occurs is that costs which may otherwise be imposed on employees are internalized by compliance orders in the cost of the product to consumers. The economic heart of OSHA is the internalization of certain external costs of unsafe or unhealthy conditions otherwise imposed, at least in part, on innocent employees.
Moreover, we agree with the ALJ’s conclusion that Faultless’ cost computations were inflated and conjectural. Faultless failed to explain various discrepancies in the figures it used to determine the number of new presses required to compensate for the alleged lost production time generated by two-hand controls. We also question the accuracy of Faultless’ computations of lost production time. According to Faultless, much of this lost production time will be caused by operators standing at their presses for seven to ten seconds as they, hold down the two-hand tripping control to activate the closing cycle. The AU found, however, that operators stand at their machines during this interval even though they now use only a one-hand start button. Further, we are puzzled by Faultless’ assertion that 21 to 30 seconds per hour (three closures per hour — Faultless’ most liberal estimate) translate into a loss of production time requiring Faultless to expand its production capacity by two presses — or more than 11%. Faultless’ most egregious error, however, has been to double count, at least in part, the cost of lost production time and capacity ($116,000) and the cost of new presses ($82,000) when the new presses are intended to compensate for the loss of capacity. Thus, we find that Faultless failed to demonstrate the infeasibility of the Secretary’s order.
Petition for review denied.