§ 23-20.11-4. Standards for cigarette fire safety.
(a) No cigarettes may be sold or offered for sale in this state or offered for sale or
sold to persons located in this state unless such cigarettes have been tested in accordance
with the test method and meet the performance standard specified in this subsection;
and a written certification has been filed by the manufacturer with the director in
accordance with § 23-20.11-5; and the cigarettes have been marked in accordance with § 23-20.11-6.
(1) Testing of cigarettes shall be conducted in accordance with the American Society of
Testing and Materials ("ASTM�) standard E2187-04 "Standard Test Method for Measuring
the Ignition Strength of Cigarettes.�
(2) Testing shall be conducted on ten (10) layers of filter paper.
(3) No more than twenty-five percent (25%) of the cigarettes tested in a test trial in
accordance with this subsection shall exhibit full-length burns. Forty (40) replicate
tests shall comprise a complete test trial for each cigarette tested.
(4) The performance standard required by this subsection shall only be applied to a complete
test trial.
(5) Written certifications shall be based upon testing conducted by a laboratory that
has been accredited pursuant to Standard ISO/IEC 17025 of the International Organization
for Standardization ("ISO�), or other comparable accreditation standard required by
the director.
(6) Laboratories conducting testing in accordance with this subsection shall implement
a quality control and quality assurance program that includes a procedure to determine
the repeatability of the testing results. The repeatability value shall be no greater
than nineteen hundredths (0.19).
(7) This section does not require additional testing if cigarettes are tested consistent
with this chapter for any other purpose.
(8) Testing performed or sponsored by the director to determine a cigarette's compliance
with the performance standard required by this section shall be conducted in accordance
with this section.
(b) Each cigarette listed in a certification submitted pursuant to § 23-20.11-5 that uses lowered permeability bands in the cigarette paper to achieve compliance
with the performance standard set forth in this section shall have at least two (2)
nominally identical bands on the paper surrounding the tobacco column. At least one
complete band shall be located at least fifteen (15) millimeters from the lighting
end of the cigarette. For cigarettes on which the bands are positioned by design,
there shall be at least two (2) bands fully located at least fifteen (15) millimeters
from the lighting end and ten (10) millimeters from the filter end of the tobacco
column, or ten (10) millimeters from the labeled end of the tobacco column for a nonfiltered
cigarette.
(c) The manufacturer or manufacturers of a cigarette that the director determines cannot
be tested in accordance with the test method prescribed in subsection (a) shall propose
a test method and performance standard for such cigarette to the director. Upon approval
of the proposed test method and a determination by the director that the performance
standard proposed by the manufacturer or manufacturers is equivalent to the performance
standard prescribed in subsection (a), the manufacturer or manufacturers may employ
such test method and performance standard to certify such cigarette pursuant to § 23-20.11-5 . If the director determines that another state has enacted reduced cigarette ignition
propensity standards that include a test method and performance standard that are
the same as those contained in this section, and the director finds that the officials
responsible for implementing those requirements have approved the proposed alternative
test method and performance standard for a particular cigarette proposed by a manufacturer
as meeting the reduced cigarette ignition propensity standards of that state's law
or regulation under a legal provision comparable to this subsection, then the director
shall authorize that manufacturer to employ the alternative test method and performance
standard to certify that cigarette for sale in this state, unless the director demonstrates
a reasonable basis why the alternative test should not be accepted under this chapter.
All other applicable requirements of this section shall apply to such manufacturer
or manufacturers.
(d) Each manufacturer shall maintain copies of the reports of all tests conducted on all
cigarettes offered for sale for a period of three (3) years, and shall make copies
of these reports available to the director and the attorney general upon written request.
Any manufacturer who fails to make copies of these reports available within sixty
(60) days of receiving a written request shall be subject to a civil penalty not to
exceed ten thousand dollars ($10,000) for each day after the sixtieth (60th) day that
the manufacturer does not make such copies available.
(e) The director may adopt a subsequent ASTM Standard Test Method for Measuring the Ignition
Strength of Cigarettes upon a finding that such subsequent method does not result
in a change in the percentage of full-length burns exhibited by any tested cigarette
when compared to the percentage of full-length burns the same cigarette would exhibit
when tested in accordance with ASTM Standard E2187-04 and the performance standard
prescribed in subsection (a) of this section.
(f) [Deleted by P.L. 2024, ch. 117, art. 3, § 11.]
(g) This chapter shall be implemented in accordance with the implementation and substance
of the New York Fire Safety Standards for Cigarettes.