This text of Indiana § 8-1-41-10 (Setback requirements; airport; public use highway, street, or road;
nonparticipating property; utility transmission or distribution line;
undeveloped residential land; state park; corporate boundaries of
municipality; blade tip height limitations; waiver of restrictions by
nonparticipating party) is published on Counsel Stack Legal Research, covering Indiana primary law. Counsel Stack provides free access to over 12 million legal documents including statutes, case law, regulations, and constitutions.
(a)Subject to subsection (h), and except as
otherwise allowed by IC 36-7-4-1109, a project owner may not install
or locate a wind power device on property in a unit unless the distance,
measured as a straight line, from the vertical centerline of the base of
the wind power device to:
(1)the centerline of any:
(A)runway located on a public use airport, private use airport,
or municipal airport;
(B)public use highway, street, or road; or
(C)railroad easement or right-of-way; or
(2)the property line of any nonparticipating property;
is equal to a distance that is at least one and one-tenth (1.1) times the
wind power device's blade tip height, as measured from the ground to
the tip of the blade.
(b)Subject to subsection (h), and except as otherwise allowed by IC 36-7-4-1109, a project o
Free access — add to your briefcase to read the full text and ask questions with AI
(a) Subject to subsection (h), and except as
otherwise allowed by IC 36-7-4-1109, a project owner may not install
or locate a wind power device on property in a unit unless the distance,
measured as a straight line, from the vertical centerline of the base of
the wind power device to:
(1) the centerline of any:
(A) runway located on a public use airport, private use airport,
or municipal airport;
(B) public use highway, street, or road; or
(C) railroad easement or right-of-way; or
(2) the property line of any nonparticipating property;
is equal to a distance that is at least one and one-tenth (1.1) times the
wind power device's blade tip height, as measured from the ground to
the tip of the blade.
(b) Subject to subsection (h), and except as otherwise allowed by IC 36-7-4-1109, a project owner may not install or locate a wind power
device on property in a unit unless the distance, measured as a straight
line, from the vertical centerline of the base of the wind power device
to the nearest point on the outer wall of a dwelling located on a
nonparticipating property is equal to a distance that is at least three (3)
times the wind power device's blade tip height, as measured from the
ground to the tip of the blade.
(c) Except as otherwise allowed by IC 36-7-4-1109, a project owner
may not install or locate a wind power device on property in a unit
unless the distance, measured as a straight line, from the vertical
centerline of the base of the wind power device to the nearest edge of
the right-of-way for any utility transmission or distribution line is equal
to a distance that is at least one and two-tenths (1.2) times the wind
power device's blade tip height, as measured from the ground to the tip
of the blade.
(d) Except as otherwise allowed by IC 36-7-4-1109, a project owner
may not install or locate a wind power device on property in a unit
unless the distance, measured as a straight line, from the vertical
centerline of the base of the wind power device to the property line of
any undeveloped land within the unit that is zoned or platted for
residential use is equal to a distance that is at least two (2) times the
wind power device's blade tip height, as measured from the ground to
the tip of the blade.
(e) Except as otherwise allowed by IC 36-7-4-1109, a project owner
may not install or locate a wind power device on property in a unit
unless the distance, measured as a straight line, from the vertical
centerline of the base of the wind power device to the property line of
a state park is equal to a distance of at least one (1) mile.
(f) A project owner may not install or locate a wind power device
within a county unless the distance, measured as a straight line, from
the vertical centerline of the base of the wind power device to the
corporate boundaries of any municipality within the county is equal to
a distance of at least one (1) mile. However, a municipality may waive
or reduce the minimum distance prescribed by this subsection with
respect to the installation of one (1) or more wind power devices.
(g) Except as otherwise allowed by IC 36-7-4-1109, a permit
authority, with respect to the permitting, construction, installation, or
siting of any wind power device within the unit, may not set a blade tip
height limitation, through a wind power regulation or otherwise, that
is more restrictive than the standards of the Federal Aviation
Administration under 14 CFR Part 77 concerning the safe, efficient use
and preservation of the navigable airspace.
(h) The distance requirements set forth in subsections (a)(2) and (b)
may be waived with respect to the siting of any one (1) wind power
device, subject to the written consent of the owner of each affected
nonparticipating property.