§ 15A-6-102 — Nitrogen Oxide emission limits for natural gas-fired water heaters.

Utah § 15A-6-102

• Jurisdiction: Utah
• Title 15A: State Construction and Fire Codes Act
• Ch. 15A-6: Additional Construction Requirements
• Part 15A-6-1: Nitrogen Oxide Emission Limits for Natural Gas-fired Water Heaters

Text

(1) As used in this section:

(1)(a) "BTU" means British Thermal Unit.
(1)(b) (1)(b)(i) "Heat input" means the heat of combustion released by fuel burned in a water heater based on the heating value of the fuel.
(1)(b)(ii) "Heat input" does not include the enthalpy of a water heater's incoming combustion air.
(1)(c) "Heat output" means the enthalpy of a water heater's working fluid output.
(1)(d) "Natural gas-fired water heater" means a device that heats water:
(1)(d)(i) using natural gas combustion;
(1)(d)(ii) for use external to the device at a pressure that is less than or equal to 160 pounds per square inch gage; and
(1)(d)(iii) to a thermostatically controlled temperature less than or equal to:

(1)(d)(iii)(A) 210 degrees Fahrenheit; or
(1)(d)(iii)(B) 99 degrees Celsius.
(1)(e) "ppm" means parts of Nitrogen Oxide per million parts of water heater air output.
(1)(f) "Recreational vehicle" means the same as that term is defined in Section 13-14-102.
(2) On and after July 1, 2018, a person may not sell or install a natural gas-fired water heater with an emission rate greater than the following limits:

(2)(a) except as provided in Subsection (6), for a water heater that has a heat input of less than or equal to 75,000 BTU per hour that is not installed in a mobile home, a limit of:
(2)(a)(i) 10 nanograms per Joule of heat output; or
(2)(a)(ii) 15 ppm, corrected to 3% oxygen;
(2)(b) for a water heater that has a heat input of greater than 75,000 BTU per hour and less than 2,000,000 BTU per hour that is not installed in a mobile home, a limit of:
(2)(b)(i) 14 nanograms per Joule of heat output; or
(2)(b)(ii) 20 ppm, corrected to 3% oxygen;
(2)(c) for a water heater installed in a mobile home, a limit of:
(2)(c)(i) 40 nanograms per Joule of heat output; or
(2)(c)(ii) 55 ppm, corrected to 3% oxygen;
(2)(d) for a pool or spa water heater with a heat input that is less than or equal to 400,000 BTU per hour, a limit of:
(2)(d)(i) 40 nanograms per Joule of heat output; or
(2)(d)(ii) 55 ppm, corrected to 3% oxygen; and
(2)(e) for a pool or spa water heater with a heat input of greater than 400,000 BTU per hour and less than 2,000,000 BTU per hour, a limit of:
(2)(e)(i) 14 nanograms per Joule of heat output; or
(2)(e)(ii) 20 ppm, corrected to 3% oxygen.
(3) A water heater manufacturer shall use California South Coast Air Quality Management District Method 100.1 to calculate the emissions rate of a water heater subject to this section.
(4) A water heater manufacturer shall display on a water heater subject to this section, as a permanent label, the model number and the Nitrogen Oxide emission rate of the water heater.
(5) The requirements of this section do not apply to:

(5)(a) a water heater using a fuel other than natural gas;
(5)(b) a water heater used in a recreational vehicle;
(5)(c) a water heater manufactured in the state for sale and shipment outside of the state; or
(5)(d) a water heater manufactured before July 1, 2018.
(6) A person may sell or install a natural gas-fired water heater with an emission rate greater than the limits established in Subsection (2)(a) if:

(6)(a) the water heater is replacing a water heater of equal BTUs per hour;
(6)(b) there is not available for purchase in the United States a water heater that:
(6)(b)(i) has an input of equal BTUs per hour as the water heater being replaced; and
(6)(b)(ii) meets the limits established in Subsection (2)(a); and
(6)(c) the purpose of the water heater is to heat water and provide space heating.

Legislative History

Amended by Chapter 136, 2020 General Session