(A)Transfer centers must:
(1)be located on a site in compliance with local zoning ordinances and have a potable water supply, wastewater and solid disposal, and air pollution facilities as required by any governmental authority having jurisdiction over the site;
(2)be covered by a metal roof or other permanent type covering with sufficient screened ventilators to allow air flow, yet preventing the entrance of rodents, birds, and insects;
(3)have walls, floors, and ceilings made of durable, nonabsorbent materials that can be cleaned and maintained in a sanitary condition;
(4)have adequate drains in an impervious floor with a supply of hot water sufficient to thoroughly clean the transfer center's building, equipment, and all vehicles transporting raw material to the transfer center; (5
Free access — add to your briefcase to read the full text and ask questions with AI
(A) Transfer centers must: (1) be located on a site in compliance with local zoning ordinances and have a potable water supply, wastewater and solid disposal, and air pollution facilities as required by any governmental authority having jurisdiction over the site; (2) be covered by a metal roof or other permanent type covering with sufficient screened ventilators to allow air flow, yet preventing the entrance of rodents, birds, and insects; (3) have walls, floors, and ceilings made of durable, nonabsorbent materials that can be cleaned and maintained in a sanitary condition; (4) have adequate drains in an impervious floor with a supply of hot water sufficient to thoroughly clean the transfer center's building, equipment, and all vehicles transporting raw material to the transfer center; (5) be cleaned and sanitized at the end of each daily operation; (6) hold inedible materials no longer than allowed by good manufacturing practices, and dispose of all product and unused raw material in a lawful manner; (7) be operated in such a manner that objectionable odors are not detected off site of the transfer center. (B) Rendering plants must: (1) be located on a site in compliance with local zoning ordinances and have a potable water supply, wastewater and solid disposal, and air pollution facilities as required by any governmental authority having jurisdiction over the site; (2) utilize buildings of sufficient size and shape to accommodate all phases of actual processing, with partitions installed therein sufficient to prevent any contact between raw materials and finished product, and to prevent contamination of finished product; (3) utilize buildings constructed with materials and in a manner that will ensure adequate drainage and sanitation in all phases of operation, and that contain walls, floors, and ceilings constructed with durable, nonabsorbent materials that can be cleaned and maintained in a sanitary manner; (4) have a supply of hot water and cleaning agents sufficient to facilitate cleaning of the building, equipment, and vehicles used to move and handle raw material and product in a sanitary manner; (5) be operated using reasonable precautions while handling, storing, or preparing raw material to prevent objectionable odors from being discharged beyond the boundaries of the permittee's property, to ensure that raw material does not remain on site any longer than allowed by good manufacturing practice, and to dispose of all product and unused raw material in a lawful manner; (6) be operated using appropriate and properly-functioning rendering equipment including, but not limited to, working, efficient, and effective odor-control systems to prevent the emission of objectionable odors; (7) diligently practice rodent and vermin control in buildings and keep surrounding grounds clean and free of refuse, trash, and manure; (8) mark all barrels used for transportation and storage of raw materials with the word "inedible" in letters clearly visible and not less than two inches in height; and (9) have a control and recontamination program, as approved by the director, that specifically provides for the prevention of cross-contamination between raw material and finished product. (C) Vehicles used to transport raw materials must: (1) be so constructed and maintained as to prevent any dripping, seeping, discharge, or escape of raw material from the truck, and have body sides of such height that no portion of the raw material transported therein is subject to spillage under normal circumstances; provided, on a case-by-case basis, the director may require the complete covering of a load of raw material for biosecurity purposes. (2) after unloading, be cleaned with hot water and a suitable cleansing agent to prevent a buildup of grease, solids, or other raw material residue, and no vehicle used to transport raw material may be taken out or operated on a public road or highway without first being thoroughly cleaned. (3) be licensed by the division as suitable for the purpose of transporting raw material.