Valve & Primer Corp. v. Val-Matic Valve & Manufacturing Corp.

730 F. Supp. 141, 14 U.S.P.Q. 2d (BNA) 1984, 1990 WL 9745, 1990 U.S. Dist. LEXIS 425
CourtDistrict Court, N.D. Illinois
DecidedJanuary 16, 1990
Docket87 C 8726
StatusPublished
Cited by4 cases

This text of 730 F. Supp. 141 (Valve & Primer Corp. v. Val-Matic Valve & Manufacturing Corp.) is published on Counsel Stack Legal Research, covering District Court, N.D. Illinois primary law. Counsel Stack provides free access to over 12 million legal documents including statutes, case law, regulations, and constitutions.

Bluebook
Valve & Primer Corp. v. Val-Matic Valve & Manufacturing Corp., 730 F. Supp. 141, 14 U.S.P.Q. 2d (BNA) 1984, 1990 WL 9745, 1990 U.S. Dist. LEXIS 425 (N.D. Ill. 1990).

Opinion

MEMORANDUM OPINION AND ORDER

HOLDERMAN, District Judge:

Plaintiff Valve & Primer Corporation (“V & P”) and defendant Val-Matic Valve and Manufacturing Corporation (“Val-Matic”) are Illinois corporations, each with its principal place of business in Illinois. The two companies manufacture valves, primers and similar equipment. V & P’s complaint alleges that it “secured the exclusive rights and privileges in and to the copyright of [certain] technical computers, bulletins, catalogs and writings” by complying with all the statutory requirements for the registration thereof provided by 17 U.S.C. § 102 et seq. (Complaint, ¶ 5.) Essentially, the complaint alleges that Val-Matic infringed twenty of plaintiff’s copyrights “by publishing and distributing numerous technical computers or ‘calculators,’ bulletins, catalogs and writings so similar to those of Plaintiff’s as to be virtually identical....” (Complaint, ¶ 8.)

V & P has agreed to voluntarily dismiss all claims pertaining to 18 of its copyright registrations. (See Plaintiff’s Response to Defendant’s 12(b) Motion, ¶¶ 5-6.) Moreover, V & P has failed to comply with this court's order of July 3, 1989 which required V & P to provide the defendant with additional information regarding its “slide rule” claim, including information regarding any copyright registration thereof. The only remaining claims in this lawsuit, therefore, pertain to the protection accorded to V & P’s publications by reason of the following two copyright registrations:

TX 331-493 for Valve and Primer Bulletin 7011 relating to the Slanting Disk *142 Check Valve as revised and republished on 6/1/78; and
TX 331-496 for Bulletin 688 relating to the Rubber Flapper Check Valve as revised and republished on 10/10/78.

(See Defendant’s 12(b) Motion, ¶¶ 7-7.2 and Plaintiffs concurrence therewith in it Response, ¶¶ 7-7.2.)

Val-Matic has filed a motion to dismiss on the ground that the court lacks subject matter jurisdiction over this case. Val-Matic contends that V & P failed to satisfy the requirements of 17 U.S.C. § 405(a) for maintaining copyright protection. The court has construed Val-Matic’s motion as one for summary judgment on the ground that V & P’s infringement claim must fail due to V & P’s failure to comply with the standards set forth in 17 U.S.C. § 405(a)(1) or (a)(2) for maintaining copyright protection. For the reasons set forth below, Val-Matic’s motion is granted.

BACKGROUND FACTS *

The remaining bulletins at issue in this case pertain to V & P’s Slanting Disc Check Valve and Rubber Flapper Check Valve. (See Motion and .Response, ¶ 9.) Bulletins 619, 7011 and 800 all pertain to the Slanting Disc Check Valve. Bulletins 688 and 100 pertain to the Rubber Flapper Check Valve. (Id.) V & P apparently contends that copyrights TX 331-493 and TX 331-496 protect these publications.

Registration TX 331-493 pertains to “APCO Slanting Disc Check Valves; Bulletin 7011.” (Exhibit A to Val-Matic’s Motion.) The effective date . of registration was May 3, 1979. Registration TX 331-498 pertains to “APCO Rubber Flapper Swing Check Valve; Bulletin 688.” (Exhibit B to Val-Matic’s Motion.) The effective date of this registration was also May 3, 1979. Both certificates of registration were not sent to V & P, however, until October 11, 1979.

The edition of Bulletin 7011 referred to in TX 331-493 was first printed in June of 1978, ie. almost 11 months prior to the May 3, 1979 effective date of copyright registration and approximately 16 months before the registration certificate was issued to V & P. (See Motion and Response, ¶ 11.) The June of 1978 version of Bulletin 7011 did not contain a notice of copyright. Bulletin 7011 was revised and reprinted in April of 1980, 22 months after the June of 1978 publication. (Id. ¶ 12.) The 1980 revision of Bulletin 7011 was never separately registered with the United States Copyright Office: V & P did, however, add a notice of copyright to the 1980 revision with a 1979 copyright date. (Motion and Response, ¶ 12.) All other subsequent revisions of Bulletin 7011 have not been registered with the United States Copyright Office.

Bulletin 688 was published in October of 1978, also without a copyright notice. The next revision of Bulletin 688, printed in November of 1979, had a 1979 copyright notice affixed. Subsequent revisions of this bulletin have not been registered with the Copyright Office. (Motion and Response, ¶ 13.)

At his deposition, V & P’s Vice President of Sales testified that the company publishes approximately 5,000 copies of these bulletins a year. (Deposition of Ralph Di-Lorenzo, pp. 13-14.) V & P’s bulletins are revised and republished when a supply runs out, when an innovation in product design makes the old bulletins obsolete or when V & P discovers a “flagrant” error in a bulletin. (DiLorenzo Dep., pp. 13-15.) On occasion, V & P will send out correction material if an error occurs in the text of a bulletin regarding a critical aspect of the item described, e.g. an inaccuracy in the dimensional table. (DiLorenzo Dep., p. 20-21.) Mr. DiLorenzo testified that although errors have occurred in the bulletins regarding the Slanting Disc Check Valve and *143 the Rubber Flapper Check Valve, the errors were not sufficient to justify republishing the material. (Id. at 15.)

The bulletins are automatically mailed to a list of consulting engineers: this list contains approximately 4500 names. (Id. at 11.) They are also sent to V & P representatives in the field, who are free to distribute them to customers. (Id. at 10-11.)

DISCUSSION

A motion for summary judgment should be granted, of course, only when “the pleadings, depositions, answers to interrogatories and admission on file, together with the affidavits, if any, show that there is no genuine issue as to any material fact and that the moving party is entitled to judgment as a matter of law.” Fed.R.Civ.P. 56(c). As the Seventh .Circuit has noted, however, once a properly-supported motion has been made, an adverse party “ ‘may not rest upon the mere allegations or denial of [its] pleading, but the adverse party’s response, by affidavits or as otherwise provided in the rule, must set forth specific facts showing that there is a genuine issue for trial.’ ” Davis v. City of Chicago, 841 F.2d 186, 188 (7th Cir.1988) (quoting Fed.R.Civ.P. 56(e), emphasis in original).

Free access — add to your briefcase to read the full text and ask questions with AI

Related

Garnier v. Andin
First Circuit, 1994
Charles Garnier, Paris v. Andin International, Inc.
36 F.3d 1214 (First Circuit, 1994)
Charles Garnier, Paris v. Andin Intern., Inc.
844 F. Supp. 89 (D. Rhode Island, 1994)

Cite This Page — Counsel Stack

Bluebook (online)
730 F. Supp. 141, 14 U.S.P.Q. 2d (BNA) 1984, 1990 WL 9745, 1990 U.S. Dist. LEXIS 425, Counsel Stack Legal Research, https://law.counselstack.com/opinion/valve-primer-corp-v-val-matic-valve-manufacturing-corp-ilnd-1990.