HICKENLOOPER, Circuit Judge.
Defendant below appeals from a decree of the District Court holding valid and infringed claims 1, 7, and 8 of patent to Rosenfeld and McCabe, No. 1,741,118, granted December 24, 1929, for a sign and method of manufacturing the same. Claim 1 is a method claim; claims 7 and 8 are product claims. We shall discuss first the product claims in suit, of which claim 7 is typical and is printed in the margin.1
For some years prior to the final development of the sign of the patent, the appellant had used round, double-faced signs of the pedestal type, about twenty-four inehes in diameter, made of 16-gauge sheet metal coated with vitreous enamel. Because of the thinness of the metal and the brittleness of the coating, these signs were often bent, or the coating was chipped off around the edges, in handling and in use. To prevent this the appellant suggested to the appellee, and to other manufacturers of such signs, that a sign be designed with a reasonably heavy reinforcing ring about the periphery of the enameled portion.
The first designs were submitted by others than the appellee, and in these the reinforcing ring was made of round tubing mashed down, bent to semicircular shape, opened up to receive the enameled sign, and the two pieces then butt welded so as to form a continuous integral ring of substantially “U” cross-section. This design was not entirely satisfactory, for it gave visual evidence, in [55]*55its roughness and at the points of welding, of the way in which it had been made. However, having been designed by others, it is a complete anticipation of the product claims in suit, unless, from the language of the claims that the channel shaped frame member is “bent into the form of a cylindrical hoop'” and that the fitting embraces “the abutting ends of said channel member,” we are to inter that the claim is limited to a structure in which the frame is fashioned from a single strip of flat metal with the attending economy of manufacture and neatness of appearance.
Another suggested method of accomplishing the desired result was to use two rings, one of which was provided with a lip or grooved extension within which the other ring (a split hoop) was sprung and there held under tension. This design required a certain amount of machining, and was obviously more costly to manufacture than the integral strip frame.
But, even if the claims are limited as above indicated, we see nothing in the experience of the appellant or in the! structure itself to indicate the exorcise of the inventive faculty in designing the frame. The problem was solely to provide a continuous metal frame of “U” cross-section into which the circular sign could be inserted, either during fabrication of the frame or afterwards. The original idea of providing the sign with such a frame was not that of the patentees, and we find too many instances in the prior patented art, where very analogous types of frames were provided for articles needing this protection, to attribute any patentable novelty to the use of an integral frame as such. See patents to Huff, No. 439,514 (1890); to Tollner, No. 433,107 (1890); to Seymouro, No. 685,695 (1901); to Bailey, No. 837,028 (1906); to White, No. 1,346,360 (1920); to Krantz, No. 1,356,375 (1920); to Suhler, No. .1,440,846 (1923); to Mastín, No. 1,583,410 (application 1923); etc. The only element of ingenuity required was in devising the method by which the frame was to be made and the sign fixed therein without injury to the enamel. Perhaps a novel method of doing this would be patentable, but not the product of such a method, for the product was neither the conception of the patentees nor had it the attribute of novelty. Cf. Nestle-Le Mur Co. v. Eugene, Ltd. (C. C. A.) 55 F.(2d) 854, 857. It was merely a new use for an old and well-known element in like environment.
Turning to the method claim printed in the margin,2 the only method disclosed by the specification is to first attach the ends of a flat strip of metal together, and then by a draw press operation to impart substantially an “L” shaped cross section to the strip1. The specification continues: “The next step in the method of manufacturing the sign is to place within this ring, successively, a ring 5 of compressible material, such as paper; the sign proper, designated 1; and a second ring 6, which is the same as ring 5. By al subsequent operation, and by moans of suitable dies, the ring is bent into the acute angular cross-sectional shape, as shown in Fig. 5. The third and final operation, performed by suitable pressure dies, imparts a channel formation to the ring, as most clearly- shown in Fig. 6, this operation completing the rigid, and permanently attached frame 2.”
The chief function of the paper rings 5 and 6 is to protect the sign when the frame is being painted, although there may be some cushioning effect protecting the enamel coating from being cracked or chipped during the final compression of the frame. Because of the assertion in the specification of the presence of this function, • we abstain from passing upon the validity of the claim now considered. It is only necessary to say in this connection that we do not find this method claim infringed.
In recent decisions we have pointed out the elemental differences between a patent for a method or process, and a patent for an article or product of manufacture (Nestle-Le Mur Co. v. Eugene, Ltd., supra), and have held that infringement of a method claim is not established merely by a showing that the defendant has accomplished the same result, if in doing so he has followed a substantially different procedure or “mode of acting.” Sherwin-Williams Co. v. California Spray Chemical Co. (C. C. A.) 61 F.(2d) 297, decided October 14, 1932. Wo have also referred to the apparent inconsistency between the doctrine of equivalents and the doctrine that it is the claim and that alone which measures the invention [Directoplate Corp. v. Donaldson Lithographing Co. (C. C. A.) 51 F.(2d) 199], hut definiteness of claim de[56]*56seription is required as much, in a process patent as in a product patent. We must first find the steps of the claimed method distinctly and clearly set forth in the claim [Cf. Sun Ray Gas Corp. v. Bellows-Claude Neon Co., 49 F.(2d) 886 (C. C. A. 6); Bettendorf Co. v. Ohio Steel Co., 56 F.(2d) 777 (C. C. A. 6)], and, if this test be met, the question then is whether the defendant has in all substantial res’pects followed the method claimed.
The steps of the method covered by the above claim are stated with precision if the claim is to be construed in the light of the specification. A circular frame of “L” cross section is first formed after “connecting the ends of the strip together,” for, unless this were done, there would be no- support for the sign when “placed within the frame.” Thereafter the upright of the “L” of the already circularly formed frame is bent down to give the frame a cross-sectional “U” shape. These operations are performed by the die or draw presses common to the sheet metal working industries. They constitute one way of achieving the desired result, but we find them lacking from the method by iwhieh the appellant’s signs are made. The latter method reverts, rather, to the split hoop type of frame disclosed in the patents to Krantz, Seymoure, and Huff, supra, with, only such modifications as were indicated by the nature of the job and the requirements of good mechanics.
In one respect only do we find substantial similarity of method.
Free access — add to your briefcase to read the full text and ask questions with AI
HICKENLOOPER, Circuit Judge.
Defendant below appeals from a decree of the District Court holding valid and infringed claims 1, 7, and 8 of patent to Rosenfeld and McCabe, No. 1,741,118, granted December 24, 1929, for a sign and method of manufacturing the same. Claim 1 is a method claim; claims 7 and 8 are product claims. We shall discuss first the product claims in suit, of which claim 7 is typical and is printed in the margin.1
For some years prior to the final development of the sign of the patent, the appellant had used round, double-faced signs of the pedestal type, about twenty-four inehes in diameter, made of 16-gauge sheet metal coated with vitreous enamel. Because of the thinness of the metal and the brittleness of the coating, these signs were often bent, or the coating was chipped off around the edges, in handling and in use. To prevent this the appellant suggested to the appellee, and to other manufacturers of such signs, that a sign be designed with a reasonably heavy reinforcing ring about the periphery of the enameled portion.
The first designs were submitted by others than the appellee, and in these the reinforcing ring was made of round tubing mashed down, bent to semicircular shape, opened up to receive the enameled sign, and the two pieces then butt welded so as to form a continuous integral ring of substantially “U” cross-section. This design was not entirely satisfactory, for it gave visual evidence, in [55]*55its roughness and at the points of welding, of the way in which it had been made. However, having been designed by others, it is a complete anticipation of the product claims in suit, unless, from the language of the claims that the channel shaped frame member is “bent into the form of a cylindrical hoop'” and that the fitting embraces “the abutting ends of said channel member,” we are to inter that the claim is limited to a structure in which the frame is fashioned from a single strip of flat metal with the attending economy of manufacture and neatness of appearance.
Another suggested method of accomplishing the desired result was to use two rings, one of which was provided with a lip or grooved extension within which the other ring (a split hoop) was sprung and there held under tension. This design required a certain amount of machining, and was obviously more costly to manufacture than the integral strip frame.
But, even if the claims are limited as above indicated, we see nothing in the experience of the appellant or in the! structure itself to indicate the exorcise of the inventive faculty in designing the frame. The problem was solely to provide a continuous metal frame of “U” cross-section into which the circular sign could be inserted, either during fabrication of the frame or afterwards. The original idea of providing the sign with such a frame was not that of the patentees, and we find too many instances in the prior patented art, where very analogous types of frames were provided for articles needing this protection, to attribute any patentable novelty to the use of an integral frame as such. See patents to Huff, No. 439,514 (1890); to Tollner, No. 433,107 (1890); to Seymouro, No. 685,695 (1901); to Bailey, No. 837,028 (1906); to White, No. 1,346,360 (1920); to Krantz, No. 1,356,375 (1920); to Suhler, No. .1,440,846 (1923); to Mastín, No. 1,583,410 (application 1923); etc. The only element of ingenuity required was in devising the method by which the frame was to be made and the sign fixed therein without injury to the enamel. Perhaps a novel method of doing this would be patentable, but not the product of such a method, for the product was neither the conception of the patentees nor had it the attribute of novelty. Cf. Nestle-Le Mur Co. v. Eugene, Ltd. (C. C. A.) 55 F.(2d) 854, 857. It was merely a new use for an old and well-known element in like environment.
Turning to the method claim printed in the margin,2 the only method disclosed by the specification is to first attach the ends of a flat strip of metal together, and then by a draw press operation to impart substantially an “L” shaped cross section to the strip1. The specification continues: “The next step in the method of manufacturing the sign is to place within this ring, successively, a ring 5 of compressible material, such as paper; the sign proper, designated 1; and a second ring 6, which is the same as ring 5. By al subsequent operation, and by moans of suitable dies, the ring is bent into the acute angular cross-sectional shape, as shown in Fig. 5. The third and final operation, performed by suitable pressure dies, imparts a channel formation to the ring, as most clearly- shown in Fig. 6, this operation completing the rigid, and permanently attached frame 2.”
The chief function of the paper rings 5 and 6 is to protect the sign when the frame is being painted, although there may be some cushioning effect protecting the enamel coating from being cracked or chipped during the final compression of the frame. Because of the assertion in the specification of the presence of this function, • we abstain from passing upon the validity of the claim now considered. It is only necessary to say in this connection that we do not find this method claim infringed.
In recent decisions we have pointed out the elemental differences between a patent for a method or process, and a patent for an article or product of manufacture (Nestle-Le Mur Co. v. Eugene, Ltd., supra), and have held that infringement of a method claim is not established merely by a showing that the defendant has accomplished the same result, if in doing so he has followed a substantially different procedure or “mode of acting.” Sherwin-Williams Co. v. California Spray Chemical Co. (C. C. A.) 61 F.(2d) 297, decided October 14, 1932. Wo have also referred to the apparent inconsistency between the doctrine of equivalents and the doctrine that it is the claim and that alone which measures the invention [Directoplate Corp. v. Donaldson Lithographing Co. (C. C. A.) 51 F.(2d) 199], hut definiteness of claim de[56]*56seription is required as much, in a process patent as in a product patent. We must first find the steps of the claimed method distinctly and clearly set forth in the claim [Cf. Sun Ray Gas Corp. v. Bellows-Claude Neon Co., 49 F.(2d) 886 (C. C. A. 6); Bettendorf Co. v. Ohio Steel Co., 56 F.(2d) 777 (C. C. A. 6)], and, if this test be met, the question then is whether the defendant has in all substantial res’pects followed the method claimed.
The steps of the method covered by the above claim are stated with precision if the claim is to be construed in the light of the specification. A circular frame of “L” cross section is first formed after “connecting the ends of the strip together,” for, unless this were done, there would be no- support for the sign when “placed within the frame.” Thereafter the upright of the “L” of the already circularly formed frame is bent down to give the frame a cross-sectional “U” shape. These operations are performed by the die or draw presses common to the sheet metal working industries. They constitute one way of achieving the desired result, but we find them lacking from the method by iwhieh the appellant’s signs are made. The latter method reverts, rather, to the split hoop type of frame disclosed in the patents to Krantz, Seymoure, and Huff, supra, with, only such modifications as were indicated by the nature of the job and the requirements of good mechanics.
In one respect only do we find substantial similarity of method. After the frame of appellant’s signs has been fashioned, the sign inserted while the split hoop is still open, and the fitting which holds the ends of the hoop together attached, the sign is covered with paper extending beneath the edges of the frame and the frame is then pressed, as in the patent to Edmunds, No. 1,657,793, more tightly against the sign. This clamping is primarily to prevent the entrance of water when the sign is completed, but it is a step similar to the last part of- the third or final step of the patented method as described in th© specification. The other steps of the patented method, however, are omitted, and we need not deeide whether a valid claim could have been based solely upon the use of paper as a cushion during final clamping, or whether the appellant, as a purchaser of the completed signs, would be liable as a contributory infringer because of- placing the order. It is enough that the claim in1 suit 'is not so limited, and that a three-step process is not infringed by a method in which two of the steps are either omitted entirely or are replaced by a “mode of acting” which is substantially different in its nature.
The decree of the District Court is accordingly reversed, and the cause is remanded, with instructions to dismiss the bill of complaint.