Cumberland Coal Resources, LP v. Federal Mine Safety & Health Review Commission

515 F.3d 247, 2008 U.S. App. LEXIS 3244, 2008 WL 399182
CourtCourt of Appeals for the Third Circuit
DecidedFebruary 15, 2008
Docket06-4192
StatusPublished
Cited by15 cases

This text of 515 F.3d 247 (Cumberland Coal Resources, LP v. Federal Mine Safety & Health Review Commission) is published on Counsel Stack Legal Research, covering Court of Appeals for the Third Circuit primary law. Counsel Stack provides free access to over 12 million legal documents including statutes, case law, regulations, and constitutions.

Bluebook
Cumberland Coal Resources, LP v. Federal Mine Safety & Health Review Commission, 515 F.3d 247, 2008 U.S. App. LEXIS 3244, 2008 WL 399182 (3d Cir. 2008).

Opinion

OPINION OF THE COURT

JORDAN, Circuit Judge.

Cumberland Coal Resources, LP (“Cumberland”) petitions for review of the August 29, 2006 decision of the Federal Mine Safety and Health Review Commission (the “Commission”) affirming the decision of an Administrative Law Judge (the “ALJ”) that upheld three citations issued to Cumberland by inspectors of the Federal Mine Safety and Health Administration (“MSHA”) on January 16, 2004, February 4, 2004, and February 7, 2004. Cumberland Coal Resources, LP v. Sec’y of Labor, Mine Safety & Health Admin., 27 F.M.S.H.R.C. 295, 2005 WL 857342 (2005) (ALJ) (“Cumberland I”), aff'd, 28 F.M.S.H.R.C. 545, 2006 WL 2587959 (2006) (“Cumberland II”). We will deny the petition, and in so doing affirm the Commission’s decision.

I. BACKGROUND

A. Factual Background

1. Longwall Mining and Bleeder Ventilation

This case grows out of problems encountered while Cumberland was using a technique called “longwall mining” to extract coal from a mine in Greene County, Pennsylvania. Longwall mining involves the use of cutting machines to shear coal from one face of a large rectangular block, or panel, of coal. In preparing to engage in longwall mining, a number of tunnels, sometimes called “entries,” are created in a coal seam, offsetting the block of coal to be mined. Some of these entries are “trav-elable,” meaning that people may safely move through them to access the mine. Mining equipment is installed directly adjacent to one of the walls of the block of coal, which wall, though it is in this instance one of the two of shorter width, becomes known as the “longwall face” and is the surface from which the coal is severed.

In addition to the shearer that severs the coal from the longwall face, the mining equipment also includes conveyor belts to transport the coal. As the cutting head of the shearer moves back and forth across *249 the longwall face, severed coal falls onto the first conveyor belt, which is positioned parallel to the face and transports the coal to a stage loader. The stage loader in turn feeds the coal onto another conveyor belt system for removal from the mine. The end of the longwall face towards which the first conveyor belt directs the severed coal for removal is called the “headgate,” and entries on that side of the panel are “headgate entries.” The opposite end is called the “tailgate,” and the entries there are “tailgate entries.”

Longwall mining requires the use of hydraulic roof supports, or shields. These shields support the roof over the area being mined, advancing with the longwall face as the coal is removed. As the shields are moved, the unsupported roof material falls behind them to create what is called the “gob.” Though it has a nontechnical ring, the word “gob” is a term of art meaning “the space left by the extraction of a coal seam into which waste is packed or the immediate roof caves.” (Respondent’s Brief at 8 n. 6 (citing Am. Geological Inst., Dictionary of Mining, Mineral and Related Terms 239 (2d ed.1997)).) In short, the term is used to describe the area behind the shields where coal has been extracted and the roof has been permitted to cave in. The gob is also sometimes referred to as the “worked-out area” or the “mined-out area.”

Because methane gas, which is noxious and potentially explosive, is released during mining, a “bleeder system” or “bleeder ventilation system” is used to ventilate worked-out areas. “Bleeder entries” are integral to the bleeder system, serving as special air courses, or pathways, designed to remove methane from areas where mining has resulted in the extraction of a substantial portion of the coal. 1 The bleeder system dilutes methane coming from the gob with fresh air coming through the bleeder entries. The entries may be connected to one another by “crosscuts,” which are small passageways usually driven at right angles to the entries. Air containing higher levels of methane exits the gob and enters the bleeder entries through connector entries that may contain adjustable ventilation control devices. The points at which air from the gob goes into the bleeder entries can be used for measuring methane concentrations and hence are called “bleeder evaluation points,” or “BEPs.”

2. Cumberland Mine

Cumberland operates Cumberland Mine, a large underground coal mine in western Pennsylvania. The mine has the unfortunate distinction of being “gassy,” which means that it typically liberates more than 1,000,000 cubic feet of methane in a twenty-four hour period and consequently requires spot inspection every five days by representatives of MSHA. 30 U.S.C. § 813(1). In a gassy longwall mine, methane is liberated from the longwall face that is being mined, as well as from within the gob. As previously noted, bleeder ventilation systems are intended to dilute and remove the liberated methane. 2

*250 This case involves ventilation problems associated with the forty-ninth longwall panel at Cumberland Mine, also known as the “No. 49 longwall panel” or “LW49.” LW49 is 12,000 feet long by 1,250 feet wide and is the largest panel Cumberland has ever undertaken to mine. Cumberland I, 27 F.M.S.H.R.C. at 315.

Pursuant to 30 C.F.R. § 75.370(a)(1), a mine operator must submit a ventilation plan to MSHA for approval before beginning to mine. Section 75.370(a)(1) provides, in pertinent part:

The operator shall develop and follow a ventilation plan approved by the district manager. The plan shall be designed to control methane and respirable dust and shall be suitable to the conditions and mining system at the mine....

The ventilation plan for LW49 was submitted to MSHA. on November 7, 2003. The type of ventilation system proposed was a “wraparound” system that would circulate bleeder air by using fans already in place for other mining operations 3 to create a pressure differential that would draw air towards and across the longwall face. Cumberland chose the wraparound system over a more conventional “bleeder fan” system, which would have drawn air to a bleeder fan and shaft that was to have been installed at the back of the area that would become the gob. 4 Though Cumberland had originally planned to use a bleeder fan system at LW49 and had laid out the entries around the panel with that in mind, it abandoned those plans when it became clear that the bleeder fan could not be installed and operational by the time Cumberland wanted to begin mining.

No matter what system it had chosen, Cumberland knew it was obligated to comply with 30 C.F.R. § 75.334(b)(1), which sets forth a mandatory safety standard every ventilation system must meet:

Free access — add to your briefcase to read the full text and ask questions with AI

Related

Cite This Page — Counsel Stack

Bluebook (online)
515 F.3d 247, 2008 U.S. App. LEXIS 3244, 2008 WL 399182, Counsel Stack Legal Research, https://law.counselstack.com/opinion/cumberland-coal-resources-lp-v-federal-mine-safety-health-review-ca3-2008.