§ 444.12 — Monitoring requirements.

40 CFR § 444.12

• Title: Title 40: Protection of Environment
• Part: Part 444: Waste Combustors Point Source Category
• Source: eCFR (current through Apr 10, 2026)

Text

§ 444.12 Monitoring requirements.

(a) Both direct and indirect discharges must monitor to establish compliance with their limitations and standards. Thus, all the permits of all direct dischargers must include requirements to monitor, according to EPA-approved test procedures, each pollutant limited in the permit, the volume of effluent discharged from each outfall, and other appropriate measurements subject to notification requirements. See 40 CFR 122.44(i). EPA's pretreatment regulations similarly require indirect dischargers to monitor to demonstrate compliance with pretreatment standards. See 40 CFR 403.12(g).

(b) Incorporation by reference:

(1) Compliance with the monitoring requirements may be accomplished using approved test procedures listed in the table to this paragraph. Most of these test procedures have previously been incorporated by reference at 40 CFR 136.3(a), Table IB. The test procedures for the regulated pollutants (arsenic, cadmium, chromium (total), copper, pH, lead, mercury, TSS, silver, titanium, and zinc) listed in the table to this paragraph are also incorporated by reference into this regulation. The full texts of the test procedures listed in this paragraph are available from the sources indicated in paragraph (b)(2) of this section. In addition to those test procedures incorporated by reference at 40 CFR 136.3(a), Table IB, you may also use EPA Method 200.8, “Determination of Trace Elements in Water and Wastes by Inductively Coupled Plasma-Mass Spectrometry,” from “Methods for Determination of Metals in Environmental Samples—Supplement I,” EPA-600/R-94-111, May 1994, and ASTM Method D 5673-96, “Standard Test Method for Elements in Water by Inductively Coupled Plasma—Mass Spectrometry,” from 1999 Annual Book of ASTM Standards, for determination of arsenic, cadmium, chromium (total), copper, lead, silver, and zinc. The full texts of these methods are incorporated by reference into this regulation and may be obtained from the sources identified in paragraph (b)(2) of this section.

List of Approved Inorganic Test Procedures

Parameter, units and method	Reference (method number or page)
	EPA 1 16	Standard Methods [18th Edition] 6	ASTM	USGS 2	Other
1. Arsenic—Total, 4 mg/L:
Digestion 4 followed by	206.5
AA gaseous hydride	206.3	3114B 4.d	D2972-93(B)	I-3062-85
AA furnace	206.2	3113B	D2972-93(C)
ICP/AES 15	5 200.7	3120 B
Colorimetric (SDDC), or	206.4	3500-As C	D2972-93(A)	I-3060-85
ICP/MS	7 200.8		D5673-96 17
2. Cadmium—Total, 4 mg/L; Digestion 4 followed by:
AA direct aspiration 15	213.1	3111 B or C	D3557-90(A or B)	I-3135-85 or I-3136-85	974.27, 3 p. 37.
AA furnace	213.2	3113 B	D3557-90(D)
ICP/AES 15	5 200.7	3120 B
DCP 15			D4190-82(88)	I-1472-85	(14)
Voltametry 9
Colorimetric (Dithizone), or		3500-Cd D	D3557-90(C)
ICP/MS	7 200.8		D5673-96 17
3. Chromium-Total, 4 mg/L; Digestion 4 followed by:
AA direct aspiration 15	218.1	3111 B	D1687-92(B)	I-3236-85	974.27. 3
AA chelation-extraction	218.3	3111 C
AA furnace	218.2	3113 B	D1687-92(C)
ICP/AES 15	5 200.7	3120 B
DCP 15			D4190-82(88)		(14)
Colorimetric (Diphenylcarbazide), or		3500-Cr D
ICP/MS	7 200.8		D5673-96 17
4. Copper—Total, 4 mg/L; Digestion 4 followed by:
AA direct aspiration 15	220.1	3111 B or C	D1688-90(A or B)	I-3270-85 or I-3271-85	974.27 3 p. 37. 8
AA furnace	220.2	3113 B	D1688-90(C)
ICP/AES 15	5 200.7	3120 B
DCP 15 or			D4190-82(88)		(14)
Colorimetric (Neocuproine) or		3500-Cu D
(Bicinchoninate), or		or E			(10)
ICP/MS	7 200.8		D5673-96 17
5. Hydrogen ion (pH), pH units:
Electrometric measurement	150.1	4500-H + B	D1293-84 (90)(A or B)	I-1586-85	973.41.
Automated electrode					(11)
6. Lead—Total, 4 mg/L; Digestion 4 followed by:
AA direct aspiration 15	239.1	3111 B or C	D3559-90(A or B)	I-3399-85	974.27. 3
AA furnace	239.2	3113 B	D3559-90(D)
ICP/AES 15	5 200.7	3120 B
DCP 15			D4190-82(88)		(14)
Voltametry 9			D3559-90(C)
Colorimetric (Dithizone), or		3500-Pb D
ICP/MS	7 200.8		D5673-96 17
7. Mercury—Total, 4 mg/L:
Cold vapor, manual or	245.1	3112 B	D3223-91	I-3462-85	977.22. 3
Automated	245.1
8. Residue—nonfilterable (TSS), mg/L:
Gravimetric, 103-105-post washing of residue	160.2	2540 D		I-3765-85
9. Silver—Total, 4 mg/L: Digestion 4 12 followed by:
AA direct aspiration	272.1	3111 B or C		I-3720-85	974.27 3 p. 37. 8
AA furnace	272.2	3113 B
ICP/AES	5 200.7	3120 B
DCP, or					(14)
ICP/MS	7 200.8		D5673-96 17
10. Titanium—Total, 4 mg/L; Digestion 4 followed by:
AA direct aspiration	283.1	3111 D
AA furnace, or	283.2
DCP					(14)
11. Zinc—Total, 4 mg/L; Digestion 4 followed by:
AA direct aspiration 15	289.1	3111 B or C	D1691-90(A) or B)	I-3900-85	974.27, 3 p. 37. 8
AA furnace	289.2
ICP/AES 15	5 200.7	3120 B
DCP 15			D4190-82(88)		(14)
Colorimetric (Dithizone) or		3500-Zn E
(Zincon), or		3500-Zn F			(13)
ICP/MS	7 200.8		D5673-96 17
Table Notes:
1 “Methods for Chemical Analysis of Water and Wastes,” Environmental Protection Agency, Environmental Monitoring Systems Laboratory—Cincinnati (EMSL-CI), EPA-600/4-79-020, Revised March 1983 and 1979 where applicable.
2 Fishman, M.J., et al. “Methods for Analysis of Inorganic Substances in Water and Fluvial Sediments,” U.S. Department of the Interior, Techniques of Water—Resource Investigations of the U.S. Geological Survey, Denver, CO, Revised 1989.
3 “Official Methods of Analysis of the Association of Official Analytical Chemists,” methods manual, 15th ed. (1990).
4 For the determination of total metals the sample is not filtered before processing. A digestion procedure is required to solubilize suspended material and to destroy possible organic-metal complexes. Two digestion procedures are given in “Methods for Chemical Analysis of Water and Wastes, 1979 and 1983”. One (Section 4.1.3), is a vigorous digestion using nitric acid. A less vigorous digestion using nitric and hydrochloric acids (Section 4.1.4) is preferred; however, the analyst should be cautioned that this mild digestion may not suffice for all samples types. Particularly, if a colorimetric procedure is to be employed, it is necessary to ensure that all organo-metallic bonds be broken so that the metal is in a reactive state. In those situations, the vigorous digestion is to be preferred making certain that at no time does the sample go to dryness. Samples containing large amounts of organic materials may also benefit by this vigorous digestion, however, vigorous digestion with concentrated nitric acid will convert antimony and tin to insoluble oxides and render them unavailable for analysis. Use of ICP/AES as well as determinations for certain elements such as antimony, arsenic, the noble metals, mercury, selenium, silver, tin, and titanium require a modified sample digestion procedure and in all cases the method write-up should be consulted for specific instructions and/or cautions. Note.—If the digestion procedure for direct aspiration AA included in one of the other approved references is different than the above, the EPA procedure must be used.
Dissolved metals are defined as those constituents which will pass through a 0.45 micron membrane filter. Following filtration of the sample, the referenced procedure for total metals must be followed. Sample digestion of the filtrate for dissolved metals (or digestion of the original sample solution for total metals) may be omitted for AA (direct aspiration or graphite furnace) and ICP analyses, provided the sample solution to be analyzed meets the following criteria:
a. Has a low COD (<20)
b. Is visibly transparent with a turbidity measurement of 1 NTU or less
c. Is colorless with no perceptible odor, and
d. Is of one liquid phase and free of particulate or suspended matter following acidification.
5 EPA Method 200.7, “Inductively Coupled Plasma Atomic Emission Spectrometric Method for Trace Element Analysis of Water and Wastes,” from “Methods for Determination of Metals in Environmental Samples—Supplement I,” EPA-600/R-94-111, May 1994.
6 “Standard Methods for the Examination of Water and Wastewater,” 18th Edition (1992).
7 EPA Method 200.8, “Determination of Trace Elements in Waters and Wastes by Inductively Coupled Plasma-Mass Spectrometry,” from “Methods for Determination of Metals in Environmental Samples—Supplement I,” EPA-600/R-94-111, May 1994.
8 American National Standard on Photographic Processing Effluents, Apr. 2, 1975. Available from ANSI, 1430 Broadway, New York, NY 10018.
9 The use of normal and differential pulse voltage ramps to increase sensitivity and resolution is acceptable.
10 Copper, Biocinchoinate Method, Method 8506, Hach Handbook of Water Analysis, 1979, Hach Chemical Company, PO Box 389, Loveland, CO 80537.
11 Hydrogen ion (pH) Automated Electrode Method, Industrial Method Number 378—75WA, October 1976, Bran & Luebbe (Technicon) Autoanalyzer II. Bran & Luebbe Analyzing Technologies, Inc., Elmsford, NY 10523.
12 Approved methods for the analysis of silver in industrial wastewaters at concentrations of 1 mg/L and above are inadequate where silver exists as an inorganic halide. Silver halides such as the bromide and chloride are relatively insoluble in reagents such as nitric acid but are readily soluble in an aqueous buffer of sodium thiosulfate and sodium hydroxide to pH of 12. Therefore, for levels of silver above 1 mg/L, 20 mL of sample should be diluted to 100 mL by adding 40 mL each of 2 M Na2 S2 O3 and NaOH. Standards should be prepared in the same manner. For levels of silver below 1 mg/L the approved method is satisfactory.
13 Zinc, Zincon Method, Method 8009, Hach Handbook of Water Analysis, 1979, pages 2-231 and 2-333, Hach Chemical Company, Loveland, CO 80537.
14 “Direct Current Plasma (DCP) Optical Emission Spectrometric Method for Trace Elemental Analysis of Water and Wastes, Method AES0029,” 1986—Revised 1991, Thermo Jarrell Ash Corporation, 27 Forge Parkway, Franklin, MA 02038.
15 “Closed Vessel Microwave Digestion of Wastewater Samples for Determination of Metals,” CEM Corporation, PO. Box 200, Matthews, NC 28106-0200, April 16, 1992. Available from the CEM Corporation.
16 Precision and recovery statements for the atomic absorption direct aspiration and graphite furnace methods, and for the spectrophotometric SDDC method for arsenic are provided in appendix D of 40 CFR part 136 and titled, “Precision and Recovery Statements for Methods for Measuring Metals.”
17 This method does not include the digestion for solids given in Method 200.8. Not using the solids digestion procedure could affect the determined concentrations. Therefore, this method may not be used for analysis of aqueous samples with suspended solids greater than 1%.

(2) The full texts of the methods from the following references which are cited in the table in paragraph (b)(1) of this section are incorporated by reference into this regulation and may be obtained from the sources identified. All costs cited are subject to change and must be verified from the indicated sources. The full texts of all the test procedures cited are available for inspection at the Analytical Methods Staff, Office of Water, U.S. Environmental Protection Agency, 1200 Pennsylvania Ave., NW., Washington, DC 20460 or at the National Archives and Records Administration (NARA). For information on the availability of this material at NARA, call 202-741-6030, or go to: http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.

Appendix to § 444.12(b)—References, Sources, Costs, and Table Citations:

(1) “Methods for Chemical Analysis of Water and Wastes,” U.S. Environmental Protection Agency, EPA-600/4-79-020, Revised March 1983 and 1979 where applicable. Available from: ORD Publications, CERI, U.S. Environmental Protection Agency, Cincinnati, Ohio 45268. [Note 1]

(2) “Standard Methods for the Examination of Water and Wastewater.” Joint Editorial Board, American Public Health Association, American Water Works Association, and Water Environment Federation, 18th Edition, 1992. Available from: American Public Health Association, 1015 15th Street NW, Washington, DC 20005. [Note 6]

(3) “Annual Book of ASTM Standards—Water and Environmental Technology,” Section 11, Volumes 11.01 (Water I) and 11.02 (Water II), 1994. [1996 for D5673-96; see Note 17]. American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.

(4) “Methods for the Determination of Metals in Environmental Samples—Supplement I”, National Exposure Risk Laboratory, Office of Research and Development, U.S. Environmental Protection Agency, Cincinnati, OH 45268, EPA 600 R-94/111, May 1994. [Notes 5 and 7]

(5) “Methods for Determination of Inorganic Substances in Water and Fluvial Sediments,” by M.J. Fishman and Linda C. Friedman, Techniques of Water Resources Investigations of the U.S. Geological Survey, Book 5 Chapter A1 (1989). Available from: U.S. Geological Survey, Denver Federal Center, Box 25425, Denver, CO 80225. Cost: $108.75 (subject to change). [Note 2]

(6) “Closed Vessel Microwave Digestion of Wastewater Samples for Determination of Metals,” CEM Corporation, P.O. Box 200, Matthews, North Carolina 28106-0200, April 16, 1992. Available from the CEM Corporation. [Note 15]

(7) “Official Methods of Analysis of AOAC—International, 15th Edition,” 1990. Price: $359.00. Available from: AOAC—International, 1970 Chain Bridge Rd., Dept. 0742, McLean, VA 22109-0742. [Note 3]

(8) “American National Standard on Photographic Processing Effluents,” April 2, 1975. Available from: American National Standards Institute, 11 West 42nd Street, New York, New York 10036. [Note 8]

(9) Bicinchoninate Method for Copper. Method 8506, Hach Handbook of Water Analysis, 1979, Method and price available from Hach Chemical Company, P.O. Box 300, Loveland, Colorado 80537. [Note 10]

(10) Hydrogen Ion (pH) Automated Electrode Method, Industrial Method Number 378-75WA. October 1976. Bran & Luebbe (Technicon) Auto Analyzer II. Method and price available from Bran & Luebbe Analyzing Technologies, Inc. Elmsford, N.Y. 10523. [Note 11]

(11) Zincon Method for Zinc, Method 8009. Hach Handbook for Water Analysis, 1979. Method and price available from Hach Chemical Company, P.O. Box 389, Loveland, Colorado 80537. [Note 13]

(12) “Direct Current Plasma (DCP) Optical Emission Spectrometric Method for Trace Elemental Analysis of Water and Wastes,” Method AES 0029, 1986 Revised 1991, Thermo Jarrell Ash Corporation (508-520-1880), 27 Forge Parkway, Franklin, MA 02038. [Note 14]

[65 FR 4381, Jan. 27, 2000, as amended at 65 FR 70315, Nov. 22, 2000; 69 FR 18803, Apr. 9, 2004]