Drift gill nets may be used to take shark and swordfish under the permit provided in this article, subject to Section 8610.3 and all of the following restrictions:
(a)From June 1 to November 15, inclusive, shark or swordfish gill nets shall not be in the water from two hours after sunrise to two hours before sunset east of a line described as follows:
From a point beginning at Las Pitas Point to San Pedro Point on Santa Cruz Island, thence to Gull Island Light, thence to the northeast extremity of San Nicolas Island, thence along the high water mark on the west side of San Nicolas Island to the southeast extremity of San Nicolas Island, thence to the northwest extremity of San Clemente Island, thence along the high water mark on the west side of San Clemente Island to the southeast extrem
Free access — add to your briefcase to read the full text and ask questions with AI
Drift gill nets may be used to take shark and swordfish under the permit provided in this article, subject to Section 8610.3 and all of the following restrictions:
(a)
From June 1 to November 15, inclusive, shark or swordfish gill nets shall not be in the water from two hours after sunrise to two hours before sunset east of a line described as follows:
From a point beginning at Las Pitas Point to San Pedro Point on Santa Cruz Island, thence to Gull Island Light, thence to the northeast extremity of San Nicolas Island, thence along the high water mark on the west side of San Nicolas Island to the southeast extremity of San Nicolas Island, thence to the northwest extremity of San Clemente Island, thence along the high water mark on the west side of San Clemente Island to the southeast extremity of San Clemente Island, thence along a line running 150° true from the southeast extremity of San Clemente Island to the westerly extension of the boundary line between the Republic of Mexico and San Diego County.
(b)
(1)
The total maximum length of a shark or swordfish gill net on the net reel on a vessel, on the deck of the vessel, and in the water at any time shall not exceed 6,000 feet in float line length. The float line length shall be determined by measuring the float line, as tied, of all the net panels, combined with any other netted lines. The existence of holes, tears, or gaps in the net shall have no bearing on the measurement of the float line. The float line of any net panels with holes, tears, or gaps shall be included in the total float line measurement.
(2)
Any shark or swordfish gill net on the reel shall have the float lines of the adjacent panels tied together, the lead lines of the adjacent panels tied together, and the web of the adjacent panels laced together. No quick disconnect device may be used unless the total maximum length of all shark and swordfish gill nets, including all spare gill nets or net panels on the vessel and all gill nets or net panels on the net reels on the vessel, on the deck of the vessel, stored aboard the vessel, and in the water, does not exceed 6,000 feet in float line length as determined under paragraph (1).
(3)
Spare shark or swordfish gill net aboard the vessel shall not exceed 250 fathoms (1,500 feet) in total length, and the spare net shall be in separated panels not to exceed 100 fathoms (600 feet) in float line length for each panel, with the float lines and leadlines attached to each panel separately gathered and tied, and the spare net panels stowed in lockers, wells, or other storage space.
(4)
If a torn panel is replaced in a working shark or swordfish gill net, the torn panel shall be removed from the working net before the replacement panel is attached to the working net.
(c)
Any end of a shark or swordfish gill net not attached to the permittee’s vessel shall be marked by a pole with a radar reflector. The reflector shall be at least six feet above the surface of the ocean and not less than 10 inches in any dimension except thickness. The permittee’s permit number shall be permanently affixed to at least one buoy or float that is attached to the radar reflector staff. The permit number shall be at least one and one-half inches in height and all markings shall be at least one-quarter inch in width.
(d)
For the purposes of this article, “shark or swordfish gill net” means a drift gill net of 14-inch or greater mesh size.