Illinois Steel Co. v. Paige

136 Ill. App. 410, 1907 Ill. App. LEXIS 640
CourtAppellate Court of Illinois
DecidedOctober 10, 1907
DocketGen. No. 4,834
StatusPublished
Cited by2 cases

This text of 136 Ill. App. 410 (Illinois Steel Co. v. Paige) is published on Counsel Stack Legal Research, covering Appellate Court of Illinois primary law. Counsel Stack provides free access to over 12 million legal documents including statutes, case law, regulations, and constitutions.

Bluebook
Illinois Steel Co. v. Paige, 136 Ill. App. 410, 1907 Ill. App. LEXIS 640 (Ill. Ct. App. 1907).

Opinion

Mr. Presiding Justice Willis

delivered the opinion of the court.

This was an action on the case brought by John D. Paige, administrator of the estate of Jay D. Paige, deceased, against the Illinois Steel Company, to recover damages for the loss of support by the next of kin of deceased, who died from injuries sustained while employed in the company’s mixer mill at Joliet, Illinois. Appellee recovered a verdict and a judgment for $6,000 from which defendant below appeals.

The declaration originally contained seven counts, each alleging that, on the 15th day of September, 1906, appellant was engaged in the manufacture of iron and steel products and was possessed of certain buildings, tools and appliances, and that deceased was employed as a weigher of molten metal in its mixer mill; and that, while in the exercise of due care for his own safety he was precipitated into molten metal, causing injuries from which he afterward died; and that he left surviving him his father, mother and seven brothers and sisters, all of whom sustained pecuniary loss by reason of his death. The court directed the jury to disregard the third and fifth counts. The negligence charged in the first count was appellant’s failure to furnish deceased with a reasonably safe place in which to work. The same was charged in the second, with the additional averment of failure to furnish a reasonably safe avenue or means of escape in the event that molten metal should be spilled. The charge in the fourth was appellant’s failure to keep in repair the buildings and appliances in the mixer 'mill; that in the sixth was the employment of a servant habitually careless and physically incompetent to-adjust certain hooks to elevate the ladles; and that in the seventh, a failure to furnish sufficient light to enable the “hooker on” to properly adjust the hooks.

The evidence shows that on the 15th day of September, 1906, appellant, the Illinois Steel Company, was engaged in the business of manufacturing iron and steel products at Joliet, Illinois, and was possessed of certain buildings and appliances; that, at that time, Jay D. Paige, the deceased, then twenty-four years old and unmarried, was an employee of appellant in its mixer mill. This was an iron or steel building eighty or one hundred feet east and west and fifty or sixty north and south, with a brick floor fifteen or eighteen feet above the ground. The east half was practically oc-. cupied by the mixers, which were large iron vessels shaped like a gravy boat, twenty-five feet long and fifteen feet wide and twenty feet high, standing north and south and side by side, with a capacity of two hundred and twenty-five tons each. In front of each of the mixers was a Howe scale, and east of the east mixer was another for the cupola iron. Over the entire mill ran two electric cranes on tracks, so constructed that they could move a load in any direction. One served the east end and the other the west end of the mill. The operators of these cranes sat in cages twenty-five or thirty feet above the floor and operated them by means of levers. A runway extended from the craneman’s cage to an iron platform outside the building, along which was an iron railing, and from which leading to the ground, were stairs. A steel or iron platform called the weigher’s platform or mixer floor, ten or eleven feet above the main floor, extended along the south wall of the mill from the east' end to within a few feet of the west end of the building. At the east end of the platform was a door or opening leading into the vessel or cupola room and a ten-foot door or opening leading into another room or building, through which access could be had down a flight of stairs to the ground. There were no openings through the south wall of the building from this platform. At the west end of the platform was a flight of stairs having a hand rail on the outside. The platform for twenty or twenty-five feet east from the stairs had a width of from four to eight feet, probably six feet, and was provided with a hand rail. It then broadened out to a width of from twelve to eighteen feet. The south end of the mixers had a nose or spout, and to make room for them to be tipped there were “V” shaped notches in the floor of the platform at this wide part. Here also in front of the nose of each mixer, was a scale beam running east and west about ten inches from the wall, and also a weight frame. The frames and beams were about four feet long and twelve inches wide. There was a hydraulic valve about three feet south and west of the nose of each mixer, to which was attached a lever about four feet long, by which the mixer was tipped. When the mixer stood upright, this handle stood to the south, and when the mixer was tipped so its contents would run out, it stood to the north. Between the end of the lever and the scale beam and frame was a distance of about four feet. There was an opening at the west end of the building about forty feet wide and twenty or twenty-five feet high where the ladles were brought in from the blast furnaces over an elevated track of ordinary railroad gauge, called the “Tónica.” There were two tracks in the west end of the mixer room for carrying the furnace ladles. The north track stopped at the west mixer, the south track ran through the mixer mill into the converter room. There was also a track from the cupolas to the east mixer, north of the other tracks, over which the ladles from the cupolas were brought in. The molten metal was brought into the mixer over the railroad tracks in ladles mounted on trucks which were drawn by an ordinary railroad engine. These ladles, holding about fifteen tons of molten metal each, standing about ten feet high on the trucks, resembled coffee cups with a spout or nose on the upper side or edge of what was always the south side as they stood on the trucks. Each ladle had upon either side round journals or trunnions about six or eight inches in diameter and fourteen inches long, which rested in the framework or saddle of the truck. There was an attachment on this saddle that caught on a lug on the journals to keep the ladles from swinging. When the ladles were on the trucks, the journals or trunnions stood east and west. In use, the ladles were picked up by the west crane by means of hooks six or eight feet long made of four by six inch steel, with the shorter end about twelve inches long, rounded at the end, and raised by means of cables attaching the hooks to the cranes. The hooks were placed on the trunnions from the north, between the ladle and the saddle of the truck, by an employee called a “hooker on.” If the metal in the ladles was to be mixed, the ladles were carried by the crane to one or the other of the mixers, and there, by means of a cable from the crane, attached to a hook on the north side of the ladle, tipped, and their contents poured into the mixer. If a “direct heat” was needed, the contents of the ladle were poured into a ladle sent out from the vessel room on the south track, and the metal went into the vessels without mixing. In taking a direct heat, owing to the fact that the ladles were pushed west of the weigher’s platform where there were no scales the necessary amount of metal to be discharged into the vessel ladle was estimated by the weigher who stood on the weigher’s platform, a process known as “guessing off.” On the night of the accident, which occurred at about eight o’clock, Paige was engaged in determining the quantity of metal to be poured into a ladle for a direct heat. He stood on the platform eight or nine feet south and west of the ladle to he lifted.

Free access — add to your briefcase to read the full text and ask questions with AI

Related

Book v. Aschenbrenner
165 Ill. App. 23 (Appellate Court of Illinois, 1911)
Swengel v. Illinois Third Vein Coal Co.
154 Ill. App. 409 (Appellate Court of Illinois, 1910)

Cite This Page — Counsel Stack

Bluebook (online)
136 Ill. App. 410, 1907 Ill. App. LEXIS 640, Counsel Stack Legal Research, https://law.counselstack.com/opinion/illinois-steel-co-v-paige-illappct-1907.