McLennan, P. J.:
The material facts'of this case are not in dispute. The defendant was engaged in manufacturing steam fire engines in the village of Seneca Falls, N. Y., and operating a foundry in connection therewith. So far as important to note, the foundry building in which the accident complained of happened was a two-story structure, the ground floor of which was used as a molding room. Directly above it was a “ scaffold room,” so called, eighteen feet eight inches long and sixteen feet wide. The walls were made of brick, and the floor of iron. It was well lighted and was reached from the molding room by means of a stairway at the south end. At the extreme north end and midway between the sides there was a cupola ór furnace for melting iron. It was a circular brick structure four feet in diameter and extended from the ground floor up through the scaffold room and roof of the building. [326]*326A door in the cupola, directly in front, opened into the scaffold room, the bottom of which was on ft level with the floor. In this room iron, coal and coke were deposited and made ready to be used in charging the cupola, it all being weighed or measured, the coal and coke placed in separate piles along the west side of the room and the iron on the east side. When the cupola was to be filled a fire was started at the bottom and the iron, coal and coke were then shoveled of thrown into it through the door from the scaffold in proper proportions. A shaft two inches in diameter extended along the west side'of the scaffold room, about eight inches from the wall and four and one-half feet 'from the floor, supported and held in place by posts or braces called “ hangers resting on the floor. The shaft was made of two pieces joined together by putting a hub or collar on each of the ends to be united. 0,n the end of each hub was a flange which projected out from the main part of the hub about one inch. Next to the flange there was a set screw which extended through the hub making it rigid upon the shaft. The head of the set screw was seven-eighths of an inch square and projected outward exactly the same distance as did the flange. When the hubs were thus attached the two ends of the shaft were connected by bolting the two flanges solidly together. . By means of a belt extending from a revolving shaft in the molding room, up through the floor of the scaffold room and onto a pulley upon the shaft in question it was caused to revolve, making about 135 revolutions per minute, and attached to it was a fan or blower connected with the cupola, which furnished a draft and caused the fire to burn more readily. The shaft throughout its entire length was uncovered and in plain view from all parts of the scaffold room.
On the 22d day of January, 1902, plaintiff’s intestate, a common laborer, sixty-five years of age, was engaged in the scaffold room assisting a Mr. Sisson, defendant’s foreman, in charging the cupola. The deceased had never worked in that room before, but had been employed by the defendant in other capacities from the fifteenth day of December previous. The fire having been started at the bottom of the cupola, the deceased, under the foreman’s direction, had shoveled the proper amount of coal and coke into the furnace ; had set down his shovel near the pile of coke on the west side of the room; had gone to the easterly side and was handing iron to Sisson, [327]*327who in turn threw it into the cupola. The iron was wet or covered with snow, so that when it came in contact with the fire it caused •steam to form, which escaped through the cupola door into the scaffold room. Sufficient iron having been thrown into the furnace, the foreman closed the door, stood close in front of it, and was peeking through a crack to see how the fire was burning. At that time, and when last seen by the foreman previous to the accident, the deceased was standing close behind him. Almost immediately thereafter the foreman heard a noise, and upon looking around saw the deceased upon the revolving shaft, which was at least seven feet from where the deceased was standing when the foreman last saw him. So far as appears, the deceased had nzo duty to perform which would lead him to go to the west side of the room, or in the vicinity of the revolving shaft. What led him to do so or how he got there is in no manner indicated by the evidence. The shaft was immediately stopped. The deceased was found upon it about midway between the coupling and the pulley, they being several feet apart, in a reclining position, his legs between the shaft and the wall of the building, his head toward the pulley, and the rest of his body extending toward •the coupling; his clothing, with the exception of his shoes and •stockings, was entirely stripped off and wound tightly about the shaft, from the pulley to and covering the coupling and the set screw above described. Fellow-workmen removed the plaintiff’s intestate from the shaft, and from the injuries sustained he died soon after.
In the complaint it is alleged that the deceased, “ while in and about his work, was caught by said projecting set screw in a portion of his clothing and was whirled around by the rapid revolution of said shaft and thereby injured and killed,” and it is alleged that the ■defendant was guilty of negligence because it failed to guard such set screw, as required by the provisions of section 81 of the Labor Law. (Laws of 1897, chap. 415, as amd. by Laws of 1899, chap. 192.) The case was tried solely upon that theory.
The only questions submitted to the jury were, in effect: First, was the deceased caught by coming in contact with the set screw; ■second, if so, was the defendant guilty of negligence in not guarding it or permitting it to remain in the condition in which it was; third, did the deceased come in contact with the set screw through [328]*328his own negligence; fourth, the amount of damage sustained because of his death.
The learned trial court charged the jury: “ It is necessary, in order to recover, that the plaintiff shall satisfy you that the deceased was killed by the negligence of the defendant in failing to guard this set screw. Of: course, if the deceased was killed not by the set screw, but by being caught by some other portion of this shaft, then the statute that defendant must properly guard set screws would have no application in this case. Then the case would simply turn • upon whether the defendant was negligent in any other way. But this is not pointed out. The only claim made here is that this accident occurred through an unguarded set screw, so. your attention must be confined entirely to that. Unless the plaintiff shows that the deceased-was killed through being" caught by, this set screw, and that it was negligence upon the part of the defendant to leave it unguarded, there can be no recovery by her, and your verdict must be for the defendant.”
The jury by its verdict must .necessarily have answered each of the questions submitted favorably to the plaintiff. The correctness of such findings is challenged by the'appellant, and it is urged that there is absolutely no evidence which, tends to support the proposi- . tion that the deceased was caught by the set screw, or that it had anything to do with throwing him upon the revolving shaft.
We think the appellant’s contention in that regard should prevail. As we have seen, no witness saw the deceased when he was caught by the shaft. When he was discovered' his body was not touching or' near the set screw or coupling.
Free access — add to your briefcase to read the full text and ask questions with AI
McLennan, P. J.:
The material facts'of this case are not in dispute. The defendant was engaged in manufacturing steam fire engines in the village of Seneca Falls, N. Y., and operating a foundry in connection therewith. So far as important to note, the foundry building in which the accident complained of happened was a two-story structure, the ground floor of which was used as a molding room. Directly above it was a “ scaffold room,” so called, eighteen feet eight inches long and sixteen feet wide. The walls were made of brick, and the floor of iron. It was well lighted and was reached from the molding room by means of a stairway at the south end. At the extreme north end and midway between the sides there was a cupola ór furnace for melting iron. It was a circular brick structure four feet in diameter and extended from the ground floor up through the scaffold room and roof of the building. [326]*326A door in the cupola, directly in front, opened into the scaffold room, the bottom of which was on ft level with the floor. In this room iron, coal and coke were deposited and made ready to be used in charging the cupola, it all being weighed or measured, the coal and coke placed in separate piles along the west side of the room and the iron on the east side. When the cupola was to be filled a fire was started at the bottom and the iron, coal and coke were then shoveled of thrown into it through the door from the scaffold in proper proportions. A shaft two inches in diameter extended along the west side'of the scaffold room, about eight inches from the wall and four and one-half feet 'from the floor, supported and held in place by posts or braces called “ hangers resting on the floor. The shaft was made of two pieces joined together by putting a hub or collar on each of the ends to be united. 0,n the end of each hub was a flange which projected out from the main part of the hub about one inch. Next to the flange there was a set screw which extended through the hub making it rigid upon the shaft. The head of the set screw was seven-eighths of an inch square and projected outward exactly the same distance as did the flange. When the hubs were thus attached the two ends of the shaft were connected by bolting the two flanges solidly together. . By means of a belt extending from a revolving shaft in the molding room, up through the floor of the scaffold room and onto a pulley upon the shaft in question it was caused to revolve, making about 135 revolutions per minute, and attached to it was a fan or blower connected with the cupola, which furnished a draft and caused the fire to burn more readily. The shaft throughout its entire length was uncovered and in plain view from all parts of the scaffold room.
On the 22d day of January, 1902, plaintiff’s intestate, a common laborer, sixty-five years of age, was engaged in the scaffold room assisting a Mr. Sisson, defendant’s foreman, in charging the cupola. The deceased had never worked in that room before, but had been employed by the defendant in other capacities from the fifteenth day of December previous. The fire having been started at the bottom of the cupola, the deceased, under the foreman’s direction, had shoveled the proper amount of coal and coke into the furnace ; had set down his shovel near the pile of coke on the west side of the room; had gone to the easterly side and was handing iron to Sisson, [327]*327who in turn threw it into the cupola. The iron was wet or covered with snow, so that when it came in contact with the fire it caused •steam to form, which escaped through the cupola door into the scaffold room. Sufficient iron having been thrown into the furnace, the foreman closed the door, stood close in front of it, and was peeking through a crack to see how the fire was burning. At that time, and when last seen by the foreman previous to the accident, the deceased was standing close behind him. Almost immediately thereafter the foreman heard a noise, and upon looking around saw the deceased upon the revolving shaft, which was at least seven feet from where the deceased was standing when the foreman last saw him. So far as appears, the deceased had nzo duty to perform which would lead him to go to the west side of the room, or in the vicinity of the revolving shaft. What led him to do so or how he got there is in no manner indicated by the evidence. The shaft was immediately stopped. The deceased was found upon it about midway between the coupling and the pulley, they being several feet apart, in a reclining position, his legs between the shaft and the wall of the building, his head toward the pulley, and the rest of his body extending toward •the coupling; his clothing, with the exception of his shoes and •stockings, was entirely stripped off and wound tightly about the shaft, from the pulley to and covering the coupling and the set screw above described. Fellow-workmen removed the plaintiff’s intestate from the shaft, and from the injuries sustained he died soon after.
In the complaint it is alleged that the deceased, “ while in and about his work, was caught by said projecting set screw in a portion of his clothing and was whirled around by the rapid revolution of said shaft and thereby injured and killed,” and it is alleged that the ■defendant was guilty of negligence because it failed to guard such set screw, as required by the provisions of section 81 of the Labor Law. (Laws of 1897, chap. 415, as amd. by Laws of 1899, chap. 192.) The case was tried solely upon that theory.
The only questions submitted to the jury were, in effect: First, was the deceased caught by coming in contact with the set screw; ■second, if so, was the defendant guilty of negligence in not guarding it or permitting it to remain in the condition in which it was; third, did the deceased come in contact with the set screw through [328]*328his own negligence; fourth, the amount of damage sustained because of his death.
The learned trial court charged the jury: “ It is necessary, in order to recover, that the plaintiff shall satisfy you that the deceased was killed by the negligence of the defendant in failing to guard this set screw. Of: course, if the deceased was killed not by the set screw, but by being caught by some other portion of this shaft, then the statute that defendant must properly guard set screws would have no application in this case. Then the case would simply turn • upon whether the defendant was negligent in any other way. But this is not pointed out. The only claim made here is that this accident occurred through an unguarded set screw, so. your attention must be confined entirely to that. Unless the plaintiff shows that the deceased-was killed through being" caught by, this set screw, and that it was negligence upon the part of the defendant to leave it unguarded, there can be no recovery by her, and your verdict must be for the defendant.”
The jury by its verdict must .necessarily have answered each of the questions submitted favorably to the plaintiff. The correctness of such findings is challenged by the'appellant, and it is urged that there is absolutely no evidence which, tends to support the proposi- . tion that the deceased was caught by the set screw, or that it had anything to do with throwing him upon the revolving shaft.
We think the appellant’s contention in that regard should prevail. As we have seen, no witness saw the deceased when he was caught by the shaft. When he was discovered' his body was not touching or' near the set screw or coupling. There is not a word of evidence which indicates that the clothing of the deceased first became fastened to the set screw, or that it was fastened to it at all. There. is notliing to show that it commenced to wind about the shaft at the point where the set screw was; that the screw was imbedded in any part of the clothing, or that any part of any garment was wound about the head of the screw, and there was nothing about the position of the body which throws any light upon the question as to how or what part of the clothing first becamo caught upon the shaft. It is a matter of common knowledge that the revolving shaft where perfectly smooth might have caught the clothing of the deceased' and caused the injury complained of. How, then, can it be said, upon [329]*329the evidence, that it was not caught at such place, but was caught by the screw? We think such conclusion must, be the result of pure speculation. It should be remembered in this connection that the set screw in question was guarded to some extent by the flange, although perhaps the jury would have been justified in finding that the defendant had not fully complied with section 81 of the Labor Law in that regard. Is it not quite as likely that the clothing of tlie deceased was caught by the nuts or heads on the bolts which fastened the two flanges together as by the set screw? Yet that was not the question submitted to the jury. They were instructed by the learned trial court that in order to enable the plaintiff to recover they must find that the set screw caused the accident, and they evidently so found. We think there is no evidence which tends to support that conclusion, and for that reason the order, must be reversed.
Neither is there any evidence which tends to prove that plaintiff’s intestate was free from contributory negligence. No one attempts to say that the deceased used proper care, or any care, as he went from the point where he was standing in front of the cupola door to the revolving shaft, a distance of seven or eight feet, even if we may assume that it was not negligent for him to go there, when he had no business connected with his employment which at the time called him to that part of the room. No one attempts to say what the deceased did when he reached the shaft, or why he went where it was. Did he attempt to sit on the revolving shaft or handle it? Did he carelessly walk too close-to it, or did he fall against it? An answer to either question must be the result of guess work and Speculation.
In O'Reilly v. Brooklyn Heights R. R. Co. (82 App. Div. 492), recently decided by the Appellate Division, second department, it was said by Mr. Justice Jenks: “It is not enough that the facts proven permit an inference, but it is held that the inference sought must be the only one which can fairly and reasonably be drawn from these facts. (Ruppert v. Brooklyn Heights R. R. Co., 154 N. Y. 90.) And naturally so, else the jury would be free for guess work.”
The rule thus stated aptly illustrates respondent’s contention in the case at bar. The jury was permitted to guess that the plaintiff’s [330]*330intestate nsed reasonable care and prudence in going in proximity to the revolving shaft, and that he was caught without any fault or negligence on his part, without any evidence to support that proposition. Whether or not he was free from negligence the evidence fails to disclose, and for that reason the order appealed from should be reVers
All concurred.
Order reversed and motion for new trial granted, with costs to appellant to abide event, upon questions of law only, the facts having been examined and no error found therein.