E. C. Miller Cedar Lumber Co. v. United States

86 F.2d 429, 24 C.C.P.A. 272, 1936 CCPA LEXIS 191
Court of Customs and Patent Appeals·Decided November 30, 1936·No. No. 4002·Published

Opinion

Hatfield, Judge,

delivered the opinion of the court:

This is an appeal from a judgment of the United States Customs Court, First Division, dismissing the protest of appellant — an American manufacturer — against the assessment of duties, by the collector at the port of Seattle, Wash., on certain imported lumber.

The merchandise in question, imported into the United States from the Dominion of Canada, is described in the brief of counsel for appellant in the following manner:

* * * (1) beveled cedar siding lumber dressed on all four sides, one-half inch thick on one side and tapering to a feather edge on the other side, by six inches in width, sawed from rough lumber ore inch in thickness by six inches in width, and (2) fir ceiling lumber, dressed and beaded on two sides, nine-sixteenths inch in thickness, by four inches in width, by four to eighteen feet in length, sawed from rough lumber three-quarters inch or twelve-sixteenths inch in thickness * * *.

That description has not been questioned by counsel for appellee, and we assume it is correct.

The collector classified the beveled cedar siding lumber as free of duty under paragraph 1803 of the Tariff Act of 1930, but assessed it with duty at $3 per thousand feet board measure, under section 601 (c) (6) of the Revenue Act of 1932, and assessed the fir ceiling lumber with duty at the rate of $1 per thousand feet board measure, under paragraph 401 of the Tariff Act of 1930, and at $3 per thousand feet board measure, under section 601 (c) (6), supra.

The pertinent parts of paragraphs 401 and 1803, supra, and section 601 (c) (6), supra, read:

Par. 401. Timber hewn, sided, or squared, otherwise than by sawing, and round timber used for spars or in building wharves; sawed lumber and timber not specially provided for; all the foregoing, if of fir, spruce, pine, hemlock, or larch, $1 per thousand feet, board measure, and in estimating board measure for the purposes of this paragraph no deduction shall be made on account of planing, tonguing, and grooving: * * *.
[274] Par. 1803. Wood:
(1) Timber hewn, sided, or squared, otherwise than by sawing, and round timber used for spars or in building wharves; sawed lumber and timber, not further manufactured than planed, and tongued and grooved; all the foregoing not specially provided for: * * *.
Sec. 601 (c) (6) Lumber, rough, or planed or dressed on one or more sides, except flooring made of maple (except Japanese maple), birch, and beech, $3 per thousand feet, board measure; but the tax on the articles described in this paragraph shall apply only with respect to the importation of such articles.

Tbe pertinent part of appellant’s protest reads:

Protestant contends that lumber of a character ordinarily produced by resawing to the thickness of less than one inch, such as bevel siding, boards, etc., and items of lumber such as ceiling, partition, boards, etc., which may be produced by the surfacing of lumber the rough size of which before surfacing was less than one inch thick, should be assessed as though such lumber were one inch thick. It has long been the common understanding in commercial practice in the measurement of lumber for sale throughout the United States to compute the board measure contents of lumber less than one inch thick as though it were one inch. This practice is universally followed throughout the lumber industry.

It appears from tbe report of tbe collector that be computed tbe “board-measure content” in tbe following manner:

Beveled Cedar Siding: In computing the board-measure content, this office took one-half of the board-measure content of the rough piece of lumber from which the board was cut.
Fir Ceiling: In computing the board-measure content of fir ceiling, this office took the invoiced rough thickness of three-fourths inch for each piece.
In the above connection this office followed the instructions contained in T. D.’s 46250 and 47621.

A motion to dismiss tbe protest was filed in tbe trial court by counsel for tbe importer, upon tbe ground that the court bad no jurisdiction to determine tbe issues in the case, because, it was claimed, the protest did not raise any question as to tbe classification or tbe rate or rates of duty assessed by tbe collector, and, therefore, did not comply with tbe provisions of section 516 (b) of tbe Tariff Act of 1930.

Tbe trial court, in an opinion by McClelland, P. J., Brown, J., specially concurring, granted tbe motion and dismissed tbe protest on tbe ground that section 516 (b), supra, hmited tbe rights of an American manufacturer to protest tbe classification by tbe collector or tbe rate or rates of duty assessed by him on imported merchandise, and that tbe protest raised neither of those issues.

Accordingly, tbe issue presented by this appeal is whether an American manufacturer’s protest against tbe method or manner of tbe collector’s determination of “board measure” raises an issue of either classification or rate or rates of duty, within tbe purview of section 516 (b), supra.

Section 516 (b) reads:

Free access — add to your briefcase to read the full text and ask questions with AI

E. C. Miller Cedar Lumber Co. v. United States, 86 F.2d 429, 24 C.C.P.A. 272, 1936 CCPA LEXIS 191 (ccpa 1936).

86 F.2d 429 (E. C. Miller Cedar Lumber Co. v. United States) — published by Counsel Stack Legal Research, free access to 12M+ legal documents.

Related

United States v. Vietor
1 Ct. Cust. 297 (Customs and Patent Appeals, 1911)
Bradford Co. v. American Lithographic Co.
12 Ct. Cust. 318 (Customs and Patent Appeals, 1924)